TMP236AQDBZRQ1
Product Specifications
TMP236AQDBZRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMP236AQDBZRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMP236AQDBZRQ1: the automotive grade of the 19.5 mV per degree sensor
TMP236AQDBZRQ1 is the AEC-Q100 grade 1 member of the TMP23x-Q1 family, in the 3-pin SOT-23 body, on a 3000 piece reel. It keeps the analog transfer of the industrial part, 400 mV at 0 degrees and 19.5 mV per degree, and adds the qualification file, the grade 1 ambient window of minus 40 to plus 125 degrees, and the marking that a automotive customer expects to find on the reel.
Grade 1 is the point of the string. The industrial TMP236 is specified from minus 10 degrees upward, which is fine inside a cabinet but not on a chassis node that sees a cold soak. The Q1 grade 1 part is specified across minus 40 to plus 125, and the document also states Functional Safety-Capable with documentation available to aid a functional safety system, which is the phrase a tier one supplier needs when the end customer asks for a safety case.
The values in the table come from SBOS939D, revised June 2022, and from the package option addendum. Two details are easy to miss and both matter at the purchase order stage: the grade split between grade 0 and grade 1 in this family, and the moisture level of 2 with a one year floor life, which is stricter than the industrial part and therefore adds a baking decision to the assembly schedule.
Grade 0 and grade 1 in the same family
The document prints TMP235-Q1 as grade 0, minus 40 to plus 150, and TMP236-Q1 as grade 1, minus 40 to plus 125. The difference is not a screening step applied to the same die; it is a published temperature window tied to the qualification, and the higher gain member is the one that stops at 125 because its output would run out of headroom above that point. At 125 degrees the output is 2.8375 V, and a 3.3 V rail leaves only 460 mV of margin, so the ceiling is electrical before it is thermal.
That is why a request for a 150 degree automotive sensor cannot simply be filled with this string. The correct route is the TMP235-Q1 grade 0 part, which has a 10 mV per degree slope and therefore reaches only 1.9 V at 150 degrees, or a different family entirely. We check the arithmetic before quoting a substitution, because a part that saturates at the top of the range produces a reading that looks plausible and is wrong.
| Function | analog output temperature sensor, automotive grade |
| Qualification | AEC-Q100 grade 1, minus 40 to plus 125 degrees |
| Sensor gain | 19.5 mV per degree Celsius, 400 mV at 0 degrees |
| Maximum error | 2.5 degrees over the specified window, 0.5 degrees typical from 0 to 70 |
| Supply range | 3.1 V to 5.5 V |
| Supply current | 10 microamps typical at 25 degrees, 14.5 microamps maximum |
| Power-on time | 800 microseconds typical |
| Output drive | 500 microamps maximum into 1000 pF |
| Line regulation | 0.02 mV per volt typical |
| Package | SOT-23, DBZ, 3 pins, 2.92 mm by 1.30 mm |
| Thermal resistance | 167 degrees per watt junction to ambient in the DBZ body |
| ESD | AEC Q100-002 human body, plus or minus 1000 V charged device |
| Safety | Functional Safety-Capable, documentation available on request |
| Carrier | 3000 pieces on a large reel |
| Moisture level | level 2 at 260 degrees, one year floor life |
| Part marking | 236Q |
| Op temperature printed | minus 40 to plus 125 on the addendum row |
Why a three pin body suits an engine bay harness
Three pins means supply, ground and output, and nothing else. There is no address to strap, no bus to arbitrate and no configuration register that can be corrupted by a glitch during a cranking event. On a harness that runs past an ignition coil the absence of a clock line is the whole argument: a digital sensor needs a filtered, protected bus, while this part needs a bypass capacitor and a series resistor into the converter.
The 167 degrees per watt figure in the SOT-23 body is better than the SC70 body of the industrial part, 275 degrees per watt, because the package has more copper area at the lead frame. At 14.5 microamps and 5.5 V the dissipation is 80 microwatts, so the die sits 0.013 degrees above the board. Self heating is not the issue; the issue is thermal lag, and the application section is direct about it: the package has to be in good thermal contact with the object being measured, otherwise the sensor reports its own neighbourhood.
For a battery management board the sensor is usually placed against a cell tab or a busbar, with a thermal pad or a copper island under the package. For an onboard charger it sits near the switching devices and reads the heatsink. In both cases the reading is only as good as the coupling, and a 2.5 degree part mounted 10 mm from the heat source can be worse than a 5 degree part mounted on it.
Reading the output in an automotive supply environment
The automotive rail is not 3.3 V. It is a 5 V rail that survives load dump through a front end clamp, and the sensor is specified to 5.5 V with 6 V absolute maximum, so it sits behind the clamp rather than on the raw rail. The line regulation of 0.02 mV per volt typical means a 100 mV rail shift moves the reading by 2 microvolts, which is 0.0001 degrees, so supply variation is not a measurable error source once the part is inside its window.
The converter side needs care. In a 12 V system the ground return carries alternator ripple and injector current, so the sensor ground and the ADC ground should meet at the sensor, not at the connector. A differential input, or a converter with a real differential multiplexer, removes most of the residual error without any calibration.
The 800 microsecond power-on time also makes the part usable in a polled architecture: the ECU can gate the sensor supply, wake it, sample it and shut it down, which keeps the quiescent load off the battery during a long park. The 10 microamp operating current makes a permanent connection viable too, so the choice is a software one rather than a hardware constraint.
Qualification paperwork a tier one will ask for
Three documents travel with this string: the AEC-Q100 qualification summary, the functional safety documentation the feature list mentions, and the package option addendum that ties the order code to the carrier and the moisture level. A purchase order that names the Q1 string but quotes an industrial price is usually a reel of the industrial part, and the difference only shows up at the qualification audit.
We keep the automotive and industrial strings on separate lines in our own stock records for exactly that reason. When a customer sends a BOM that mixes the two, we query the line rather than substitute, and the component traceability report we issue for automotive builds records the grade, the date code and the reel for every lot that goes onto the line.
The moisture level 2 rating adds a step that the industrial part does not have. The reel has a one year floor life out of the bag, and if the bag has been open longer than that, or if the humidity indicator card shows the wrong colour, the parts need baking before reflow. That is a scheduling item, not a technical risk, but it is the kind of item that stops a line at 2 am if nobody planned for it.
Where the part is used, and where it is not
The document lists automotive head unit, electric power steering, shifter system, battery management system and gasoline engine as applications. In practice the string turns up in battery packs, charger inlets, DC to DC modules and motor housings, and it is also used outside the automotive world wherever a customer wants the grade 1 window in a three pin body, for example in a ruggedised telecom remote unit or a downhole tool that has to survive a cold start.
It is not the right part for a 150 degree location, for a location that needs a digital bus and an address, or for a board that needs a calibrated reading better than 2.5 degrees without a calibration step. For those cases the remote diode sensors and the digital families on our power management cross reference page are the better starting points, and the incoming inspection plan page describes how we sample an automotive reel when it arrives.
Three questions buyers ask about this string
Is the die the same as the industrial TMP236? The transfer function and the gain are the same, the qualification and the specified window are not. Treat them as two products that share a silicon centre, not as one product with a label.
Can the reel be split? The addendum prints a single 3000 piece large reel for this row and no small reel, so a partial quantity comes from a distributor cut rather than from the vendor. We mark such cuts on the paperwork because the traceability chain changes.
Does the part need a pull-up or a filter? No pull-up, because the output is an analog voltage. A 0.1 microfarad bypass at the supply pin and, on a noisy harness, a 1 k series resistor with a 10 nF capacitor at the converter input are enough, and the series resistor also protects the converter if the sensor is replaced while the board is powered.