TMP112D0IDPWR
Product Specifications
TMP112D0IDPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMP112D0IDPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMP112D0IDPWR: half a degree in an 0.8 mm package
The TMP112D0IDPWR is a digital temperature sensor in a five pin X2SON package measuring 0.8 mm by 0.8 mm, part of the TMP112 family that runs from 1.4 V to 3.6 V with a quiescent current of about 3.2 microamps. The D0 version is specified at plus or minus 0.5 C maximum from 0 to 65 C and plus or minus 1 C over the wider range, with a 12 bit result and 0.0625 C resolution.
The family is built around supply noise rejection. The D versions are optimised for different rails, one for 3.3 V, one for 1.8 V and one for 1.5 V and above, and the accuracy figures are quoted at the rail the version was tuned for. That is why the same part number is offered in three supply variants: the silicon is the same, the behaviour at a given rail is not.
The package is the other half of the story. The 1.6 mm SOT563 body was already small; the X2SON version is a quarter of the footprint, which is what allows a sensor to sit next to the component it measures rather than at the edge of the board.
Key data for the TMP112D0IDPWR
| Function | Digital temperature sensor with a two wire interface |
| Accuracy | Plus or minus 0.5 C maximum from 0 to 65 C, plus or minus 1 C from minus 40 to 125 C |
| Resolution | 12 bit, 0.0625 C per step |
| Supply | 1.4 V to 3.6 V |
| Current | 3.2 microamps typical quiescent |
| Package | X2SON, 5 pins, 0.8 mm by 0.8 mm |
| Interface | I2C and SMBus, up to four addresses |
| Alert | Programmable alert with a fault queue |
| Versions | Supply variants tuned for 3.3 V, 1.8 V and 1.5 V rails |
| Temperature range | Minus 40 to 125 C operation |
| Ordering | TMP112D0IDPWR, large tape and reel |
Why the rail determines the accuracy figure
A digital sensor converts a small analog voltage that is proportional to temperature. The reference for that conversion comes from the supply, and any noise on the supply appears in the result. A part tuned for a 3.3 V rail has its reference and its timing optimised for that rail; running it at 1.5 V changes the noise floor and the settling behaviour.
That is why the data sheet quotes separate accuracy for each version rather than one number for the family. Reading only the headline figure and choosing the cheapest version is how a product ends up with a temperature reading that jumps by a degree when a nearby converter switches.
Decoupling is part of the same story. A 100 nanofarad capacitor within a millimetre of the supply pin, with a short return path to the ground plane, does more for accuracy than any register setting. On a 0.8 mm package, that means the capacitor is placed first and the sensor second.
The fault queue, and why one bad reading should not raise an alarm
The alert output can be configured to require several consecutive faults before it asserts. A single noisy conversion on a board with a switching supply will otherwise raise an alert that the host then has to filter in software.
A queue of two or four conversions filters that without adding hardware, and the cost is a delay equal to the conversion rate times the queue length. A product that needs a fast response cannot use a long queue, and a product that needs a stable alarm should.
The alert can also work as a comparator, staying asserted while the temperature is outside the window, or as an interrupt that clears when the host reads the register. Both behaviours are valid, and mixing them up produces a fan that runs until the board is power cycled.
Where it fits in a build
Medical instruments, wearables, handheld devices and any product where a half degree matters over a narrow range. The 1.4 V minimum supply suits a single cell, and the 0.8 mm body suits a board that is already dense.
In a medical build the accuracy claim has to be traceable, not just stated. The medical device components page sets out the records we hold, and the supplier scorecard page covers how a source is scored across a programme on delivery and quality rather than on price alone.
The sourcing side of this part is covered on the supplier quality audit. For a sensor whose accuracy figure is tied to a rail, that page covers what we confirm about the version before a reel is accepted.
Questions we get on this code
Which version suits a 1.8 V board? The version tuned for 1.8 V, not the 3.3 V one. The order code carries the version, and the accuracy figures differ between them.
Can it run on 5 V? No. The maximum supply is 3.6 V, and a 5 V rail needs a regulator or a different part.
Does the alert need a pull up? Yes, it is an open drain output. The pull up can go to the host rail rather than the sensor rail if the host runs at a different level.
How many on one bus? Four addresses, so four devices unless a multiplexer is used. Confirm the address pins are strapped before the board is released.