TLC352IDR
Product Specifications
TLC352IDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TLC352IDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TLC352IDR: dual differential comparator in an 8 pin SOIC on reels, industrial grade and active
TLC352IDR is the active industrial dual comparator, same 8 pin body as the LM393 with CMOS input current and a 2.7 V supply floor in a SOIC body of 8 pins. The I suffix is minus 40 to 85 C and the DR suffix is the 8 pin SOIC on a 2500 piece reel, the version the current addendum lists as active. Two comparators draw 150 microamps typical for the pair, the offset is 5 mV maximum at 25 C and 7 mV across the range, and the response is 200 nanoseconds at 10 mV of overdrive. Body marking is 352I and the output is open drain with a 16 mA sink.
Order code and package
| Order code | TLC352IDR |
| Function | dual differential comparator, open drain output |
| Package | SOIC, 8 pins, body code D, 2500 piece reel |
| Lifecycle | active production |
| Supply range | 2.7 to 16 V, 18 V absolute maximum |
| Supply current | 150 microamps typical, 300 maximum at 5 V |
| Response time | 200 nanoseconds at 10 mV overdrive, 100 at 100 mV |
| Output sink | 6 mA typical, 16 mA maximum |
| Input offset voltage | 1 mV typical, 5 mV maximum at 25 C, 7 over the range |
| Input bias current | 5 picoamps typical, 0.6 nanoamps maximum |
| Temperature range | minus 40 to 85 C, I suffix |
| Datasheet | SLCS016B, revision of June 2025 |
Electrical parameters that decide the application
| Input offset voltage | 1 mV typical, 5 mV maximum at 25 C, 7 mV over the range |
| Input bias current | 5 picoamps typical, 0.6 nanoamps maximum |
| Input offset current | 1 picoamp typical |
| Common mode range | 0 to VDD minus 1 V, VDD minus 1.5 V over temperature |
| Low output level | 150 mV typical, 400 maximum at 4 mA |
| Low level output current | 6 mA typical, 16 mA maximum |
| Supply current at 2.7 V | 65 microamps typical, 150 maximum |
| Response at 10 mV overdrive | 200 nanoseconds |
| Response at 100 mV overdrive | 100 nanoseconds |
| Input resistance | 10 to the twelfth ohm typical |
| Output leakage | 0.1 nanoamps typical in the off state |
| Electrostatic rating | 2000 V human body model |
Points to check before this part goes on a BOM
The industrial grade in the reel packing is the combination a new build should specify. The function, the 5 mV offset and the 150 microamp pair current are the same as the commercial part, and the only differences are the temperature floor and the top of the offset window at temperature.
Overdrive is the whole timing story on this part: 100 nanoseconds at 100 mV, 200 nanoseconds at 10 mV, and slower still below that. A 10 mV sense signal against a 5 mV worst case offset leaves 5 mV of overdrive, which is half the condition the datasheet number was taken at.
The input bias current at 0.6 nanoamps maximum is small but not zero, and on a 10 megohm bridge it is 6 mV, larger than the offset. A 1 megohm bridge sees 0.6 mV, which is a tenth of the offset and normally acceptable, and below 100 kohm the bias term disappears.
The common mode window reaches ground but stops 1 V below the positive rail, dropping to 1.5 V below over temperature. A comparator that watches a supply rail therefore senses a divided version, and the divider ratio and its tolerance become part of the threshold accuracy.
Two outputs tied together make a wired OR window detector with one pull-up resistor. The rise time is set by the pull-up and the load capacitance, and the fall time by the 16 mA sink, so a 10 kohm pull-up with 50 pF gives a rise time near half a microsecond against a fall time near 20 nanoseconds.
The part is a functional replacement for the LM393 in the same 8 pinout with the same open drain behaviour, which is why it appears in so many second source lists. The difference a repair bench notices is the input bias current and the lower sink current, not the pinout.
The 2500 piece reel and the 330 mm diameter follow the standard for the 8 pin SOIC, so a line already running an LM393 in that body needs no feeder change. That is the practical reason an LM393 to TLC352 conversion is usually a BOM edit rather than a line qualification project.
On a 2.7 V rail the common mode window is only 0 to 1.2 V at room temperature and the pair draws 65 microamps, so a low voltage board gains current but loses headroom. A 2.5 V reference is outside the window and a divided rail sense is the only arrangement that stays inside it at both ends of the range.
Where this order code fits
Industrial volume builds that need the minus 40 C floor: outdoor telecom and energy cabinets, motor control boards with a fast overcurrent trip, and instrument front ends that sense a bridge through a high impedance network. It is also the standard upgrade path for an LM393 socket where the standby current or the input bias current is the problem. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.
Questions buyers ask
Is this code active? Yes, the industrial reel is the active order code. The tube packed TLC352ID on the same die is obsolete, so a BOM change to the R suffix is all that is needed.
What is the fastest it can switch? 100 nanoseconds with 100 mV of overdrive and 200 nanoseconds with 10 mV. Below the offset limit there is no defined response at all.
Can it sense a rail directly? No. The input common mode stops 1 V below the supply, so a rail sense needs a divider or a low side arrangement.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.