Contact Us

TLC352CDR

Brand: Texas Instruments
Texas Instruments TLC352CDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TLC352CDR — Power Management & Signal Chain | Superb Automation

TLC352CDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TLC352CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TLC352CDR: dual differential comparator in an 8 pin SOIC on reels, commercial grade and active

TLC352CDR is the reel packed commercial dual comparator, the part that answers an LM393 socket with a tenth of the current in a SOIC body of 8 pins. The DR suffix is the 8 pin SOIC on a 2500 piece reel and the C grade covers 0 to 70 C. Two independent comparators draw 150 microamps typical for the pair at 5 V, respond in 200 nanoseconds at 10 mV of overdrive, and present 5 picoamps of input bias current. The body marking is 352C, the output is open drain and pin compatible with the LM393, and the part works from 2.7 V to 16 V.

Order code and package

Order codeTLC352CDR
Functiondual differential comparator, open drain output
PackageSOIC, 8 pins, body code D, 2500 piece reel
Lifecycleactive production
Supply range2.7 to 16 V, 18 V absolute maximum
Supply current150 microamps typical, 300 maximum for two comparators
Response time200 nanoseconds at 10 mV overdrive, 100 at 100 mV
Output sink6 mA typical, 16 mA maximum
Input offset voltage1 mV typical, 5 mV maximum at 25 C
Input bias current5 picoamps typical, 0.6 nanoamps maximum
Temperature range0 to 70 C, C suffix
DatasheetSLCS016B, revision of June 2025

Electrical parameters that decide the application

Input offset voltage1 mV typical, 5 mV maximum at 25 C, 6.5 mV over 0 to 70 C
Input bias current5 picoamps typical, 0.6 nanoamps maximum
Input offset current1 picoamp typical
Common mode range0 to VDD minus 1 V, VDD minus 1.5 V over temperature
Low output level150 mV typical, 400 maximum at 4 mA
Low level output current6 mA typical, 16 mA maximum
Supply current at 2.7 V65 microamps typical, 150 maximum
Response at 10 mV overdrive200 nanoseconds
Response at 100 mV overdrive100 nanoseconds
Input resistance10 to the twelfth ohm typical
Output leakage0.1 nanoamps typical in the off state
Electrostatic rating2000 V human body model

Points to check before this part goes on a BOM

The 150 microamp pair current is the reason to choose this part over an LM393, whose supply current is in the milliamp range. On a 5 V rail the difference is about 3.5 mW, which over a year is 31 watt hours, and in a battery product that is the difference between a two year and a five year service interval.

Response of 200 nanoseconds at 10 mV of overdrive is fast enough for a current mode supply, but the overdrive has to be there. A 20 mV current sense signal through a 10 milliohm shunt at 2 A gives 20 mV, and with a 5 mV offset the worst case overdrive is 15 mV, which keeps the delay near the datasheet figure.

The input common mode stops 1 V below the positive rail at 25 C and 1.5 V below over temperature, so a high side current sense at the rail is outside the window. Low side sensing, or a divider, is the normal arrangement on this part; the alternative is a dedicated high side amplifier.

Output sink is 6 mA typical and 16 mA maximum at a 1.5 V drop, and the logic low level is 400 mV at 4 mA. Driving an optocoupler directly at 10 mA is at the top of the useful range and leaves no margin for a hot board, so a transistor stage is the safer choice for a solid state relay.

Open drain outputs can be tied together to make a wired OR, which is how two comparators form a window detector with a single pull-up. The pull-up value sets both the rise time and the current in the low state, and a 4.7 kohm resistor on a 5 V rail draws about 1 mA per output, which is seven times the whole comparator supply current.

The 2500 piece reel is the standard packing for this body. Tape width and pocket size follow the 8 pin SOIC convention, so a feeder set for an LM393 SOIC will run this part without adjustment, which is the practical reason a line conversion takes an afternoon rather than a week.

The offset window at temperature is 6.5 mV for the commercial grade, so a threshold detector sized on the 5 mV room temperature limit has 1.5 mV more uncertainty in a cabinet that reaches 70 C. In a 20 mV current sense that is 7.5 percent of the signal, which is the sort of number that decides whether a trip point can be set once or has to be trimmed per unit.

Where this order code fits

Volume boards that place the part automatically: switch mode supplies that need a fast overcurrent comparator, battery chargers with a termination detector, sensor threshold cards and any board replacing an LM393 to cut standby current. The 2.7 V minimum supply also makes it usable directly from a lithium cell without a boost stage. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Reduce Component Cost page.

Questions buyers ask

Is this a drop in replacement for the LM393? The pinout and the open drain output match, the supply range covers the same rails and the input common mode includes ground. The sink current is lower, so check any load above about 10 mA.

How much current does it save? About 150 microamps for the pair against milliamps for a bipolar comparator. On a 5 V rail that is roughly 3.5 mW, which is the figure to use in a battery life calculation.

Can it run from a 3 V rail? Yes, down to 2.7 V, and the supply current falls to about 65 microamps at that rail. The usable input window becomes 0 to 2 V at room temperature.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.