TLC339IDR
Product Specifications
TLC339IDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TLC339IDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TLC339IDR: quad micropower comparator in a 14 pin SOIC on reels, industrial temperature and active
TLC339IDR is the industrial grade four comparator package in the packing TI still builds, on 2500 piece reels in a SOIC body of 14 pins. The I suffix covers minus 40 to 85 C and the DR suffix is the 14 pin SOIC on a 2500 piece reel, which is the version listed as active production. Four open drain comparators draw 44 microamps typical, the offset is 5 mV maximum at 25 C and 7 mV across the range, and the response is 2.5 microseconds at 5 mV of overdrive. The body marking is TLC339I.
Order code and package
| Order code | TLC339IDR |
| Function | quad differential comparator, open drain output |
| Package | SOIC, 14 pins, body code D, 2500 piece reel |
| Lifecycle | active production |
| Supply range | 3 to 16 V, 18 V absolute maximum |
| Supply current | 44 microamps typical, 80 maximum at 25 C |
| Response time | 2.5 microseconds at 5 mV overdrive, 4.5 at 2 mV |
| Output sink | 8 to 20 mA per output |
| Input offset voltage | 1.4 mV typical, 5 mV maximum at 25 C, 7 over the range |
| Common mode range | 0 to VDD minus 1 V, VDD minus 1.5 V over temperature |
| Temperature range | minus 40 to 85 C, I suffix |
| Datasheet | SLCS119B, revision of December 2006 |
Electrical parameters that decide the application
| Input offset voltage | 1.4 mV typical, 5 mV maximum at 25 C, 7 mV over the range |
| Input bias current | 5 picoamps typical at 25 C |
| Input offset current | 1 picoamp typical, 0.3 nanoamps hot |
| Common mode rejection | 84 dB typical |
| Supply rejection | 85 dB typical from 5 to 10 V |
| Low output level | 300 mV typical, 400 maximum at 6 mA |
| High level leakage | 0.8 nanoamps typical at 5 V |
| Supply current over temperature | 100 microamps maximum for four comparators |
| Propagation at 2 mV overdrive | 4.5 microseconds typical |
| Propagation at 10 mV overdrive | 1.7 microseconds typical |
| Offset stability | 0.23 microvolts per month including the first 30 days |
| Output current rating | 20 mA absolute maximum per output |
Points to check before this part goes on a BOM
This is the order code to move a tube packed industrial BOM onto. Same die, same 14 pin SOIC footprint, same electrical table, active lifecycle and a 2500 piece reel, so the change is a packing change and not a requalification of the circuit.
The four comparators are independent but share a die, so their offsets track. On a four cell lithium pack that means all four thresholds move together with temperature by up to 2 mV beyond their 25 C value, and the balance between cells is preserved even though the absolute thresholds move.
Response time against overdrive is the number to put in a timing budget: 4.5 microseconds at 2 mV, 2.5 at 5 mV and 1.7 at 10 mV. A protection comparator that must act within 5 microseconds needs at least 5 mV of overdrive on the worst case unit, which is twice the maximum offset.
The open drain output means the high level is set by the pull-up and the leakage, not by the part. Leakage is 0.8 nanoamps typical at 5 V and rises with temperature, so a 1 megohm pull-up at 85 C can develop 1 mV or more of drop in the off state, which some logic inputs read as a low.
Supply current of 100 microamps maximum over the range is what makes this part usable in a loop powered transmitter, where the whole budget is 4 mA and every amplifier and comparator shares it. Four comparators at 100 microamps is 2.5 percent of that budget.
The 20 mA per output absolute maximum is a survival figure. Driving an optocoupler at 10 mA through a 330 ohm resistor from 5 V is a normal load, and four of them at once puts 40 mA through the package ground, which is why the ground pin has its own trace to the plane.
The industrial reel code is the one a distributor will quote without a lifecycle warning. A buyer holding a tube packed part number for a repair order should expect a note about the packing change rather than a note about the silicon, and the reel is orderable in 2500 piece multiples, which is also the minimum quantity a line conversion normally needs.
The 14 pin SOIC shares the standard quad comparator pinout, so a board that already holds an LM339 or an older TLC339 can take this part without a change to the copper. What changes is the sink current, 16 mA on the bipolar device against 20 mA here, and the input bias current, which falls from nanoamps to picoamps and can make a divider that was tuned for the bipolar part read a different threshold.
Where this order code fits
Industrial control boards that already run the LM339 pinout and need the lower current: four rail monitors in a power supply, four thermistor thresholds on a heat sink, a fault bus that pulls one interrupt line through the open drain outputs, and battery pack boards that watch four cell groups. The minus 40 C floor makes it usable in outdoor cabinets. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.
Questions buyers ask
Is this the active industrial order code? Yes. The packaging addendum lists TLC339IDR as active production on a 2500 piece reel, while the tube packed TLC339ID is obsolete.
How does it compare with an LM339? Same four comparator function and pinout, with about one twentieth of the supply current and CMOS input leakage instead of bipolar bias current. The output sink is lower, 20 mA against the bipolar part, so heavier loads stay on the bipolar device.
What is the temperature limit? Minus 40 to 85 C for the I grade, with the offset limit rising from 5 mV at 25 C to 7 mV across that range.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.