TLC339CDR
Product Specifications
TLC339CDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TLC339CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TLC339CDR: quad micropower comparator in a 14 pin SOIC on 2500 piece reels
TLC339CDR is the reel packed commercial version of the four comparator package that draws 200 microwatts and answers in 2.5 microseconds in a SOIC body of 14 pins. The DR suffix is the 14 pin SOIC on a 2500 piece reel and the C grade runs 0 to 70 C. Four open drain comparators share one supply pin pair at 44 microamps typical and 80 maximum, the input common mode reaches VDD minus 1 V, and the output sinks 8 to 20 mA with a 400 mV low level at 6 mA. Response is 2.5 microseconds at 5 mV of overdrive, 4.5 microseconds at 2 mV and 1.7 microseconds at 10 mV.
Order code and package
| Order code | TLC339CDR |
| Function | quad differential comparator, open drain output |
| Package | SOIC, 14 pins, body code D, 2500 piece reel |
| Supply range | 3 to 16 V, 18 V absolute maximum |
| Supply current | 44 microamps typical, 80 maximum for four comparators |
| Response time | 2.5 microseconds at 5 mV overdrive, 4.5 at 2 mV |
| Output sink | 8 to 20 mA per output |
| Input offset voltage | 1.4 mV typical, 5 mV maximum at 25 C |
| Input bias current | 5 picoamps typical at 25 C, 0.6 nanoamps at 70 C |
| Common mode range | 0 to VDD minus 1 V, VDD minus 1.5 V over temperature |
| Temperature range | 0 to 70 C, C suffix |
| Packing status | active production, 2500 per reel |
| Datasheet | SLCS119B, revision of December 2006 |
Electrical parameters that decide the application
| Input offset voltage | 1.4 mV typical, 5 mV maximum at 25 C, 6.5 mV over 0 to 70 C |
| Input bias current | 5 picoamps typical, 60 picoamps maximum at 25 C |
| Input offset current | 1 picoamp typical, 0.3 nanoamps at 70 C |
| Common mode rejection | 84 dB typical |
| Supply rejection | 85 dB typical from 5 to 10 V |
| Low output level | 300 mV typical, 400 maximum at 6 mA, 650 at 70 C |
| High level leakage | 0.8 nanoamps typical at 5 V, 1 microamp at 70 C |
| Supply current over temperature | 100 microamps maximum from 0 to 70 C |
| Propagation at 2 mV overdrive | 4.5 microseconds typical |
| Propagation at 10 mV overdrive | 1.7 microseconds typical |
| Output current rating | 20 mA absolute maximum per output |
| Offset stability | 0.23 microvolts per month including the first 30 days |
Points to check before this part goes on a BOM
Response time is 4.5 microseconds at 2 mV of overdrive and 2.5 at 5 mV, and the maximum offset on this part is 5 mV. A slow crossing that only just passes the threshold therefore can never see the overdrive the timing figure was taken at, which is the single most common reason a CMOS comparator appears slower on a bench than in the datasheet.
The four comparators share one ground pin and one supply pin. At 6 mA on each output the ground pin carries 24 mA, and the lead and bond wire resistance adds a common step that shifts the effective threshold of the other three channels. A board that loads all four outputs at once sees crosstalk through the ground pin rather than through the inputs.
Offset is 1.4 mV typical and 5 mV maximum at 25 C, and the four sections of one package come from the same die, so their offsets are correlated. A window comparator built from two sections therefore shifts as a unit by up to 13 mV over temperature rather than staying centred, which matters if the window width is what protects a cell.
Input leakage rises from 5 picoamps at 25 C to 600 picoamps at 70 C. On a 1 megohm divider that is 0.6 mV at 70 C against 5 microvolts at room temperature, so a high impedance threshold network sized on the bench figure has 0.6 mV of drift it did not expect.
The C grade stops at 70 C while the I grade on the same die runs to 85 C and the Q grade to 125 C. Because the part is a common quad comparator pinout, a board that needs 85 C can move to TLC339IDR without a board change, which is why the temperature grade is often the only thing that changes between two order codes on one BOM.
Reel quantity is 2500 pieces and the tube version is a separate order code. Mixing the two in one line item is a packing error rather than a part error, but it stops a pick and place line, and the reel diameter of 330 mm is what the feeders are set for.
Where this order code fits
Production boards that place the part with a pick and place machine rather than a hand iron: battery management boards with four threshold detectors, appliance control panels with a keypad matrix scan, and multi channel alarm cards where the open drain outputs share one wired OR line into a controller interrupt. The reel packing is the reason this order code exists next to the tube version. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Consolidation page.
Questions buyers ask
What is the reel quantity? 2500 pieces on a 330 mm reel for this SOIC order code. The tube packed version is a different order code and is not interchangeable on an automated line.
How does the 2 mV overdrive case behave? Propagation stretches to 4.5 microseconds typical, and on a unit at the 5 mV offset limit there is no overdrive at all, so the delay is not bounded by the datasheet number.
Can it work from a 3.3 V rail? Yes. The supply range starts at 3 V, but the input common mode then stops at 2.3 V at 25 C and 1.8 V over temperature, so a threshold referenced to the rail needs a divider.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.