Contact Us

TLC271CDR

Brand: Texas Instruments
Texas Instruments TLC271CDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TLC271CDR — Power Management & Signal Chain | Superb Automation

TLC271CDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TLC271CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TLC271CDR: programmable bias LinCMOS operational amplifier with three power settings, on tape and reel

TLC271CDR is a single CMOS operational amplifier whose supply current and speed are selected by the voltage on one pin, from 25 microwatts to 3.4 milliwatts in a SOIC body of 8 pins. The C suffix covers 0 to 70 C and the DR suffix is the 8 pin SOIC on tape and reel. Pin 8 is the bias select input: tied to VDD it selects high bias at 3.37 mW with a 1.7 MHz bandwidth and 3.6 V per microsecond, tied to the midpoint it gives 0.755 mW with 0.5 MHz and 0.4 V per microsecond, and tied to ground it gives 25.5 microwatts with 90 kHz and 0.03 V per microsecond. Offset null pins are provided for the 10 mV grade.

Order code and package

Order codeTLC271CDR
Functionsingle operational amplifier, LinCMOS, programmable bias
PackageSOIC, 8 pins, body code D, tape and reel
Supply range3 to 16 V, 18 V absolute maximum
Bias select high3.37 mW, 1.7 MHz, 3.6 V per microsecond at 5 V
Bias select medium0.755 mW, 0.5 MHz, 0.4 V per microsecond at 5 V
Bias select low25.5 microwatts, 90 kHz, 0.03 V per microsecond at 5 V
Input offset voltage10 mV maximum at 25 C
Input resistance10 to the twelfth ohm typical
Output currentplus or minus 30 mA absolute maximum
Offset nullpins 1 and 5 on the D body
Temperature range0 to 70 C, C suffix
DatasheetSLOS090D, revision of March 2001

Electrical parameters that decide the application

Bias mode voltageVDD for high, ground for low, 1 V to VDD minus 1 V for medium
Power dissipation, high3.37 mW at 5 V, 25 C
Power dissipation, medium0.755 mW at 5 V, 25 C
Power dissipation, low25.5 microwatts at 5 V, 25 C
Slew rate, high3.6 V per microsecond
Slew rate, medium0.4 V per microsecond
Slew rate, low0.03 V per microsecond
Bandwidth, high1.7 MHz typical
Bandwidth, medium0.5 MHz typical
Bandwidth, low90 kHz typical
Voltage noise, high25 nanovolts per root hertz at 1 kHz
Voltage noise, low68 nanovolts per root hertz at 1 kHz
Open loop gain, high231 V per mV typical

Points to check before this part goes on a BOM

The three modes are not a fine adjustment, they are three different amplifiers in one package. Bandwidth moves by a factor of nineteen between high and low bias, and the noise moves the other way, from 25 to 68 nanovolts per root hertz. A circuit that changes mode at run time changes its settling behaviour, its noise and its stability margin at the same moment, so the compensation has to hold at both ends.

The medium mode needs a voltage between 1 V and VDD minus 1 V on the bias pin, and the datasheet recommends the midpoint of the supply rails. A two resistor divider from VDD to ground does that on a single supply, but the divider current is a permanent load that can exceed the 0.755 mW the medium mode is trying to save, so 1 megohm resistors are the practical floor.

The bias select pin is a high impedance input, not a logic gate. It has to be driven to a defined level at all times: leaving it floating does not select a default mode, it leaves the operating point undefined. A microcontroller pin with a 1 megohm pull-down covers the case where the controller is in reset.

Offset is 10 mV on this grade, and the null pins are the reason the 8 pin body exists in this family. A 100 kohm potentiometer between pins 1 and 5 with the wiper to VDD trims the offset, but the trim is only as stable as the potentiometer and the supply it references, so a 10 mV part trimmed at test is not the same as a 2 mV graded part over temperature.

Power dissipation of 25.5 microwatts in low bias is the whole point of the part, and it is 3.4 mW in high bias, a factor of 132. A 2000 mAh cell runs for 7 years at the low setting and 20 days at the high setting, which is why the mode change has to be under firmware control rather than fixed at assembly.

At 0.03 V per microsecond in low bias, a 2 V step takes 67 microseconds to slew, and a 10 bit converter sampling at 100 kSPS has only 10 microseconds per conversion. The low bias setting is for slow monitoring, not for a multiplexed data acquisition front end.

Where this order code fits

Instruments that must change power state at run time: a portable meter that runs slow and cheap while logging and fast while sampling, a battery powered sensor node that wakes for a burst of measurements, or a loop powered transmitter that has to keep its own consumption under 4 mA. The bias pin is driven from a microcontroller output, so the same board serves both modes without a second amplifier. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Reduce Component Cost page.

Questions buyers ask

How is the bias mode selected? By the voltage on pin 8. VDD selects high bias, ground selects low bias, and a voltage between 1 V and VDD minus 1 V selects medium bias with the midpoint recommended.

Does the offset grade change with the bias mode? No. The 10 mV limit belongs to the amplifier and is specified at 5 V; what changes with bias is bandwidth, slew rate, noise and supply current.

Can one pin really switch power that far? It switches the internal bias current, so the quiescent power follows: 3.37 mW at high bias and 25.5 microwatts at low bias, with 0.755 mW in between. The output stage current is separate and comes from the load.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.