Contact Us

TL974QPWRQ1

Brand: Texas Instruments
Texas Instruments TL974QPWRQ1 is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL974QPWRQ1 — Power Management & Signal Chain | Superb Automation

TL974QPWRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL974QPWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL974QPWRQ1: quad rail to rail output operational amplifier in a 14 pin TSSOP, automotive qualified

TL974QPWRQ1 is four amplifiers on a 2.7 V to 12 V supply with a 10.6 MHz gain bandwidth product and 65 milliamps of output current per channel in a TSSOP body of 14 pins. The Q1 suffix is the automotive qualification and the PW suffix is the 14 pin TSSOP. On a plus or minus 2.5 V supply the offset is 0.21 mV typical and 4 mV maximum at 25 C, 6 mV over the minus 40 to plus 125 C range, drift is 0.25 microvolts per degree, the gain bandwidth product is 10.6 MHz, the noise is 4.4 nanovolts per root hertz at 100 kHz, and each output can source or sink 65 milliamps.

Order code and package

Order codeTL974QPWRQ1
Functionquad rail to rail output operational amplifier
PackageTSSOP, 14 pins, body code PW
Supply range2.7 V to 12 V recommended, 15 V absolute maximum
Gain bandwidth10.6 MHz
Output current65 mA source and sink per channel
Offset voltage0.21 mV typical, 4 mV maximum at 25 C
Offset over full range6 mV maximum
Offset drift0.25 microvolts per degree
Input common modeminus 1.35 V to plus 1.35 V on plus or minus 2.5 V
Temperature rangeminus 40 to plus 125 C
Qualificationautomotive Q1

Electrical parameters that decide the application

Bias current10 picoamps typical, 750 nanoamps maximum, 1000 nanoamps over range
Input offset current10 picoamps typical, 150 nanoamps maximum
Voltage noise4.4 nanovolts per root hertz at 100 kHz
Common-mode rejection60 dB minimum, 90 dB typical
Supply rejection60 dB minimum, 70 dB typical
Large-signal gain70 dB minimum, 125 dB typical into 2 kilohms
Output high2 V minimum, 2.4 V typical into 2 kilohms
Output lowminus 2.4 V typical, minus 2 V maximum
ESD ratingplus or minus 2500 V human body model, new die
Junction temperature150 C maximum
Differential input limitplus or minus 1 V
PackageTSSOP, 14 pins

Points to check before this part goes on a BOM

Rail to rail on this part describes the output, and the input is a different question. The input common mode window is minus 1.35 V to plus 1.35 V on a plus or minus 2.5 V supply, so it does not reach either rail, and a 3.3 V single supply board has to keep both inputs between roughly 0.3 V and 3 V. The output can swing to the rails; the input cannot.

The differential input limit is plus or minus 1 V, which is small. Any circuit that puts a large differential voltage across the inputs during a fault or a transient, such as a comparator with hysteresis or a current sense amplifier during a short circuit, will exceed it and needs series resistors to limit the current.

Bias current is 10 picoamps typical and 750 nanoamps maximum, a factor of 75000 between the two columns. That is a CMOS input with a leakage specification that is dominated by the test limit rather than by the input structure, so a high impedance source has to be evaluated against the maximum column and not the typical.

The 65 milliamp output current is large for a quad in a TSSOP and it is the reason the package matters. Four channels at 65 milliamps and 1 V of drop is 260 milliwatts in the output stages alone, on a 14 pin TSSOP with a thermal resistance that will not pass that in still air at 125 C ambient.

The 4 mV maximum offset at 25 C with 0.25 microvolts per degree of drift is an unusual combination: over 165 degrees the drift is only 41 microvolts, so the offset is essentially constant. That makes the part easy to calibrate once, which is what an automotive sensor interface needs over its temperature range.

The gain bandwidth product of 10.6 MHz is quoted with a 2 kilohm load and 100 picofarads, which is a heavy load for a 10 MHz amplifier. At that load the phase margin is close to the stability limit, and a capacitive load above 100 picofarads needs a series resistor at the output to keep the response from peaking.

Where this order code fits

Automotive sensor interfaces, motor control current sense amplifiers and infotainment audio stages use this part because it runs from the 3.3 V or 5 V rail in the car, tolerates 125 C, and drives enough current for a cable or a small actuator. The rail to rail output also makes it usable on a 3.3 V rail where every millivolt of swing counts. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Does rail to rail apply to the inputs as well as the outputs? To the outputs only. The input common mode window is minus 1.35 V to plus 1.35 V on plus or minus 2.5 V rails, which leaves roughly 1.1 V at each end of a single 3.3 V supply unreachable.

What makes the Q1 suffix different from the plain part? The automotive qualification flow, the minus 40 to plus 125 C temperature range and the associated test programme. The electrical limits are written for that range rather than for a commercial one.

Can it drive a 50 ohm cable? 65 milliamps into 50 ohms is 3.25 V, so it can drive 2 V peak to peak into 50 ohms, but the dissipation at 125 C ambient makes that a short duty cycle application rather than a continuous one.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.