Contact Us

TL084CDR

Brand: Texas Instruments
Texas Instruments TL084CDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL084CDR — Power Management & Signal Chain | Superb Automation

TL084CDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL084CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL084CDR: quad JFET input operational amplifier in a 14 pin SOIC with a 3 MHz gain bandwidth

TL084CDR is four TL08x amplifiers on one die, with the 5 V per microsecond guaranteed slew rate and a 65 picoamp bias current per input in a SOIC body of 14 pins. The 14 pin D suffix carries four amplifiers with the TL08x table: 3 mV typical and 10 mV maximum offset, 3 MHz gain bandwidth, 5 V per microsecond minimum slew rate, 1.4 milliamps typical supply current each and 18 nanovolts per root hertz of noise. Four amplifiers at the maximum column is 10 milliamps, so the supply and thermal budget is the quad's real constraint.

Order code and package

Order codeTL084CDR
Functionquad JFET input operational amplifier
PackageSOIC, 14 pins, body code D
Supply rangeplus or minus 2.25 V to plus or minus 20 V
Supply current1.4 mA typical, 2.5 mA maximum per amplifier
Package current5.6 mA typical, 10 mA maximum
Gain bandwidth3 MHz per amplifier
Slew rate5 V per microsecond minimum, 20 typical
Offset voltage3 mV typical, 10 mV maximum at 25 C
Bias current65 picoamps typical, 200 picoamps maximum
Temperature range0 to 70 C, C suffix
DatasheetSLOS081O, revision of September 2025

Electrical parameters that decide the application

Offset drift18 microvolts per degree
Offset over full range13 mV maximum
Voltage noise18 nanovolts per root hertz at 1 kHz
Common-mode rejection70 dB minimum, 100 dB typical
Open-loop gain25 to 200 V per mV
Output swingplus or minus 13.5 V into 10 kilohms
Output swing into 2 kilohmsplus or minus 12 V typical
Input common modeplus or minus 11 V typical on 15 V rails
Input resistance1 teraohm
Total harmonic distortion0.003 percent at 6 V RMS
Thermal path14 pin SOIC lead frame
EMI rejection53 dB at 1 GHz

Points to check before this part goes on a BOM

Four amplifiers sharing one package means one supply decoupling point for four signal paths. A single 100 nanofarad capacitor at the package is the minimum, and a board that puts the capacitor 20 mm away through a via has already given up most of the rejection the part offers.

Package current of 10 milliamps at the maximum column is the supply budget number, not 5.6 milliamps. At 15 V rails that is 300 milliwatts of quiescent heat before any output load, and a 14 pin SOIC with a 100 C per watt junction to ambient sits 30 degrees above the surrounding air.

The 5 V per microsecond slew floor limits a full amplitude signal to about 80 kHz at 10 V peak to peak. Four channels of a 100 kHz filter therefore need the TL074 rather than this part, and the difference is not visible in the 3 MHz gain bandwidth figure that both share.

Every input has a 65 picoamp typical bias current, and the four inputs are independent, so a board cannot assume that a low impedance source on one channel protects the others. Each channel's source impedance sets its own offset contribution, and a 1 megohm source on channel three is 65 microvolts of offset that the other channels do not have.

These are among the most counterfeited analogue parts in circulation, because the pinout is shared with several families and the marking is easy to reproduce. Buying through a channel that can show date code, packaging and country of origin is the difference between a part that meets the 3 MHz table and one that does not.

The output stage has a resistive current limit rather than a foldback, so a fault on one channel drags the shared supply. On a four channel card that means one failed sensor can take down the other three, and series resistors on each output are the usual protection.

Where this order code fits

Four channel integrators, multi pole filters and industrial signal conditioning cards use this part, particularly where each channel has a high impedance source that a bipolar input would load. It is also common in educational and hobby boards, which makes it one of the parts most often counterfeited, so traceability matters when buying. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is the TL084 a drop in for the TL074? Pin compatible, but the TL074 has an 8 V per microsecond guaranteed slew rate against 5 for this part, so the TL074 can replace the TL084 and not the reverse.

What is the real supply current for four channels? Ten milliamps at the maximum column for the amplifiers alone, plus load current. Four channels at 1 V into 10 kilohms add 400 microamps.

Can this part be used at plus or minus 15 V? Yes, that is the standard condition for the whole table, with a 40 V total supply ceiling. At plus or minus 15 V the input common mode reaches about plus or minus 11 V and the output about plus or minus 13.5 V into 10 kilohms.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.

Package heat with four channels driving loads

The quiescent term is easy to miss because the per amplifier figure is small. At the maximum column of 2.5 milliamps per amplifier on plus or minus 15 V rails, one channel is 75 milliwatts, and four channels are 300 milliwatts before any output current flows; a 14 pin SOIC with a junction to ambient figure near 100 C per watt sits 30 degrees above the surrounding air on that alone.

Add the output stages and the number grows by a third. A channel holding 5 V into a 2 kilohm load passes 2.5 milliamps with 10 V across the output device, which is 25 milliwatts, and four such channels add 100 milliwatts. The package then dissipates 400 milliwatts and the junction sits 40 degrees above ambient, so a cabinet at 70 C puts the die at 110 C, which is inside the 150 C limit but leaves 40 degrees for a hot spot or a blocked vent.

That is also why four channels at full load are not the same as four channels at low load. A card that drives 10 kilohm loads can hold 5 V on all four outputs for 2 milliwatts each, and the package stays at the quiescent 300 milliwatts. Moving to 2 kilohm loads adds a third to the heat for the same signal, and the thermal answer changes without any change in the circuit.