TL082CDR
Product Specifications
TL082CDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TL082CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TL082CDR: dual JFET input operational amplifier with a 3 MHz gain bandwidth in an 8 pin SOIC
TL082CDR is the wide supply JFET dual from the TL08x family, with a guaranteed 5 V per microsecond slew rate and the same 18 nanovolt noise floor as the TL07x in a SOIC body of 8 pins. The TL08x table is close to the TL07x table and differs in the guaranteed slew rate: 5 V per microsecond minimum for the C and B grades against 8 for the TL07xC. Offset is 3 mV typical and 10 mV maximum at 25 C, 13 mV over the commercial window, gain bandwidth is 3 MHz and supply current is 1.4 milliamps typical per amplifier.
Order code and package
| Order code | TL082CDR |
| Function | dual JFET input operational amplifier |
| Package | SOIC, 8 pins, body code D |
| Supply range | plus or minus 2.25 V to plus or minus 20 V |
| Supply current | 1.4 mA typical, 2.5 mA maximum per amplifier |
| Gain bandwidth | 3 MHz |
| Slew rate | 5 V per microsecond minimum, 20 typical for the C grade |
| Offset voltage | 3 mV typical, 10 mV maximum at 25 C |
| Offset drift | 18 microvolts per degree |
| Bias current | 65 picoamps typical, 200 picoamps maximum |
| Temperature range | 0 to 70 C, C suffix |
| Datasheet | SLOS081O, revision of September 2025 |
Electrical parameters that decide the application
| Offset over full range | 13 mV maximum |
| Input offset current | 5 picoamps typical, 100 picoamps maximum |
| Voltage noise | 18 nanovolts per root hertz at 1 kHz |
| Integrated noise | 4 microvolts RMS from 10 Hz to 10 kHz |
| Common-mode rejection | 70 dB minimum, 100 dB typical |
| Open-loop gain | 25 to 200 V per mV |
| Output swing | plus or minus 13.5 V into 10 kilohms |
| Input common mode | plus or minus 11 V typical |
| Total harmonic distortion | 0.003 percent at 6 V RMS |
| Input resistance | 1 teraohm |
| Settling time | 0.1 microseconds to 0.1 percent |
| EMI rejection | 53 dB at 1 GHz |
Points to check before this part goes on a BOM
The only guaranteed difference from the TL072C in the current revision is the slew rate floor: 5 V per microsecond here against 8 V per microsecond there. Everything else in the two tables is the same, which means a board that needs the faster edge should order the TL07x part and a board that does not can use either.
The two families were historically different in the input stage bias network and in the output stage, and the current data sheet has brought the tables together. Anyone comparing a 1980s data book with the 2025 revision will find different numbers, and the current document is the one that describes the part shipping today.
A 5 V per microsecond slew rate limits a 10 V peak to peak sine to 80 kHz, and a 20 V peak to peak sine to 40 kHz, regardless of the 3 MHz gain bandwidth. Most circuits built around this part run well below those frequencies, which is why the lower slew rate never shows up in practice.
Offset of 10 mV maximum with 18 microvolts per degree of drift means the drift over the commercial window is 1.26 mV, about an eighth of the initial offset. Trimming the offset at production test is therefore worth doing and trimming it at temperature is not.
The JFET input at 65 picoamps typical makes this part usable with a 10 megohm feedback resistor, where a bipolar input would contribute millivolts of offset. Above about 100 megohms the board leakage, not the amplifier, sets the error, and a guard ring around the input node becomes necessary.
Output swing into 10 kilohms is plus or minus 13.5 V on 15 V rails, but the output stage current limit is resistive, so a shorted output pulls the rail down through the output resistance rather than folding back. On a shared supply with other parts, one shorted output can take the whole board down.
Where this order code fits
This part appears in circuits that need a JFET input with a wide supply and do not need the last few volts per microsecond of slew rate: integrators, sample and hold stages, low frequency filters and voltage controlled oscillators. It is also the common second source on boards that were written around the TL08x pinout and its input bias network. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Is the TL082 a drop in replacement for the TL072? The pinout and the supply range are the same and the tables are nearly identical, with a 5 V per microsecond slew floor against 8. Substituting the TL082 into a TL072 socket is safe at low frequency and marginal for fast edges.
Why is the offset 10 mV and not 1 mV? The part is trimmed to a commercial window rather than a precision one. 3 mV typical is what most units do, and 10 mV is the maximum a unit can show and still ship. A precision stage needs a different family.
Does it work at plus or minus 5 V? Yes, down to plus or minus 2.25 V total supply. At plus or minus 5 V the input common mode is roughly plus or minus 1.5 V and the output swing is about plus or minus 3.5 V into 10 kilohms.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.