Contact Us

TL074IDR

Brand: Texas Instruments
Texas Instruments TL074IDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL074IDR — Power Management & Signal Chain | Superb Automation

TL074IDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL074IDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL074IDR: quad low noise JFET input operational amplifier in a 14 pin SOIC, industrial grade

TL074IDR is four JFET input amplifiers with the same 3 MHz and 18 nanovolt core as the dual, specified over the minus 40 to plus 85 C industrial window in a SOIC body of 14 pins. The I suffix is the industrial grade, and the data sheet gives that grade a tighter offset than the commercial part: 3 mV typical and 6 mV maximum at 25 C, 8 mV over the industrial window, against 10 and 13 mV for the C grade. Four amplifiers at 1.4 milliamps typical each put the package at 5.6 milliamps, and 10 milliamps at the maximum column, so the 14 pin body has to pass that current as heat.

Order code and package

Order codeTL074IDR
Functionquad JFET input operational amplifier
PackageSOIC, 14 pins, body code D
Supply rangeplus or minus 2.25 V to plus or minus 20 V
Supply current1.4 mA typical, 2.5 mA maximum per amplifier
Package current5.6 mA typical, 10 mA maximum with four active
Gain bandwidth3 MHz per amplifier
Slew rate8 V per microsecond minimum, 20 typical
Offset voltage3 mV typical, 6 mV maximum at 25 C
Offset over full range8 mV maximum, I grade
Temperature rangeminus 40 to plus 85 C, I suffix
DatasheetSLOS080W, revision of July 2025

Electrical parameters that decide the application

Offset drift18 microvolts per degree
Bias current65 picoamps typical, 200 picoamps maximum
Bias current over temperature7 nanoamps at the range limit
Voltage noise18 nanovolts per root hertz at 1 kHz
Common-mode rejection70 dB minimum, 100 dB typical
Open-loop gain25 to 200 V per mV
Output swingplus or minus 13.5 V into 10 kilohms
Output swing into 2 kilohmsplus or minus 12 V typical
Total harmonic distortion0.003 percent at 6 V RMS, 1 kHz
Input resistance1 teraohm common mode
Crosstalkmeasured per channel pair on the quad
EMI rejection53 dB at 1 GHz

Points to check before this part goes on a BOM

The industrial grade is tighter on offset than the commercial grade, not looser. Six millivolts maximum at 25 C and 8 mV over minus 40 to plus 85 C against 10 mV and 13 mV for the C part, so paying for the I suffix buys accuracy as well as temperature range, which is the opposite of the usual assumption.

Four amplifiers in a 14 pin SOIC at 2.5 milliamps maximum each is 10 milliamps, which at 15 V rails is 300 milliwatts in the package. The 14 pin SOIC junction to ambient is around 100 C per watt, so the die sits 30 degrees above ambient before any load current, and a cabinet at 70 C puts the junction at 100 C.

Drift of 18 microvolts per degree over the 125 degree industrial span is 2.25 millivolts, which is a third of the 6 mV initial offset. Over the full range the part is therefore within 8 mV, which is consistent with the table, and the offset is dominated by the room temperature term rather than by drift.

The 25 V per mV minimum open-loop gain is 88 dB, which is modest for a precision stage. At a closed loop gain of 100 the loop has only 48 dB of gain left, so the gain error is 0.4 percent and the distortion at 1 kHz is set by that error rather than by the output stage. High gain stages need a part with more open-loop gain.

Common mode range of plus or minus 11 V on 15 V rails leaves 4 V of headroom at each rail, and it is asymmetric in the sense that the input stage works best near the middle. A high side current sense that sits 13 V above ground is outside the window and the amplifier will show a phase inversion rather than a clipping output.

All four amplifiers share the supply pins and the die, so thermal crosstalk is a real mechanism: a channel driving a heavy load heats the die and shifts the offset of the other three by the drift coefficient. At 18 microvolts per degree, a 10 degree rise from a hot channel is 180 microvolts on the neighbours, which is small next to 6 mV but visible on a 16 bit channel.

Where this order code fits

Four channel data acquisition front ends, multi pole active filters and industrial control boards use this part, and the industrial grade is what makes it usable in a cabinet that reaches 70 C inside. The quad also suits instrumentation amplifier builds where three or four matched stages sit on one die at the same temperature. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Why is the I grade offset better than the C grade? The industrial part is trimmed and screened to a tighter window as well as tested over the wider temperature range. 6 mV maximum against 10 mV, and 8 mV against 13 mV over the full range.

Can all four amplifiers drive loads at once? Yes, within the package thermal limit. Four channels at 2 kilohm loads and 5 V outputs dissipate about 200 milliwatts in the output stages alone, on top of 300 milliwatts of quiescent power, which is more than a 14 pin SOIC can pass in still air.

Is this a drop in for the TL084? Same pinout and supply range. The TL084 has a 5 V per microsecond guaranteed slew rate against 8 for this part, so the TL074 is the faster of the two and can replace the TL084, but not the other way round.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Medical Device Components page sets out the checks that keep a substitute from failing on the bench.