Contact Us

TL072CDR

Brand: Texas Instruments
Texas Instruments TL072CDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL072CDR — Power Management & Signal Chain | Superb Automation

TL072CDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL072CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL072CDR: dual low noise JFET input operational amplifier in an 8 pin SOIC body

TL072CDR is the reference JFET input dual that runs at 3 MHz with 18 nanovolts per root hertz of noise and a 65 picoamp bias current at room temperature in a SOIC body of 8 pins. The C suffix is the 0 to 70 C grade and the D suffix is the 8 pin SOIC. The current revision of the data sheet puts the C grade at 3 mV typical and 10 mV maximum offset at 25 C, 13 mV over the commercial window, 3 MHz of gain bandwidth, 1.4 milliamps of supply current per amplifier and 18 nanovolts per root hertz at 1 kHz, with a minimum slew rate of 8 V per microsecond and 20 V per microsecond typical.

Order code and package

Order codeTL072CDR
Functiondual JFET input operational amplifier
PackageSOIC, 8 pins, body code D
Supply rangeplus or minus 2.25 V to plus or minus 20 V, 4.5 to 40 V total
Supply current1.4 mA typical, 2.5 mA maximum per amplifier
Gain bandwidth3 MHz
Slew rate8 V per microsecond minimum, 20 V per microsecond typical
Offset voltage3 mV typical, 10 mV maximum at 25 C
Offset drift18 microvolts per degree
Bias current65 picoamps typical, 200 picoamps maximum
Temperature range0 to 70 C, C suffix
DatasheetSLOS080W, revision of July 2025

Electrical parameters that decide the application

Offset over full range13 mV maximum for the C grade
Input offset current5 picoamps typical, 100 picoamps maximum
Bias current over temperature7 nanoamps at the range limit
Voltage noise18 nanovolts per root hertz at 1 kHz, 4 microvolts RMS from 10 Hz to 10 kHz
Common-mode rejection70 dB minimum, 100 dB typical
Supply rejection70 dB minimum, 100 dB typical
Open-loop gain25 to 200 V per mV into 10 kilohms
Output swingplus or minus 13.5 V into 10 kilohms, plus or minus 12 V into 2 kilohms
Input common modeplus or minus 11 V typical, 12 to 15 V below the positive rail
Total harmonic distortion0.003 percent at 6 V RMS and 1 kHz
EMI rejection53 dB at 1 GHz
Output impedance125 ohms at 1 MHz

Points to check before this part goes on a BOM

The slew rate in the current revision is not the 13 V per microsecond figure that older data books printed. The C grade now carries a guaranteed minimum of 8 V per microsecond and a typical of 20, so a timing calculation built on the old number is neither conservative nor correct, and a board qualified against it should be rechecked.

The 200 picoamp bias current is a 25 C number. At the top of the commercial window the same table gives 7 nanoamps, a factor of 35, which through a 1 megohm source is 7 millivolts. A high impedance stage that measures well on the bench at 25 C can drift a long way in a warm enclosure.

Offset of 10 mV maximum is the weakest specification on the part and the reason it is not a precision amplifier. It is also the reason this part is cheap and everywhere: for ac coupled audio and for filters with a blocking capacitor, the offset never reaches the signal and the user never sees it.

The output swing into 2 kilohms falls to plus or minus 10 V minimum on 15 V rails, from plus or minus 12 V into 10 kilohms. A stage that has to drive a 600 ohm load through a capacitor is limited by the output stage, not by the rail, and the margin lost is about 4 V peak to peak.

Noise of 18 nanovolts per root hertz at 1 kHz rises at lower frequencies, and the 10 Hz to 10 kHz integrated figure is 4 microvolts RMS. For an audio path that is inaudible, and for a low level sensor that integrates over seconds it is the dominant error, because 1/f noise integrates without bound.

The JFET input stage limits the common mode range to about 4 V below the positive rail. A follower tracking a signal up to the positive rail will hit the input limit before the output limit, and beyond that point the input stage inverts and the output jumps to the opposite rail, which on a 15 V supply is a 24 V excursion into whatever is downstream.

Where this order code fits

Audio signal paths, active filters, sample and hold buffers and guitar and instrument preamps use this part because the JFET input keeps the bias current in the picoamp range while the 18 nanovolt noise stays low enough for a moving coil or piezo source. It is also the standard second source for the many boards that were laid out around this pinout. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is the TL072CDR the same part as the TL072CP? Same die and same grade, different package. The CP suffix is the 8 pin DIP and the CDR is the 8 pin SOIC in tape and reel, so the electrical table is identical and only the thermal resistance differs.

What slew rate should go into a timing calculation? The 8 V per microsecond minimum from the current revision, not the 13 V figure in older books and not the 20 V typical. A full power bandwidth of 8 divided by two pi times the peak voltage is the safe number.

Can this part run from a single 5 V supply? It can, from 4.5 V total. The input common mode then sits about 1.5 V below the positive rail and the output cannot reach either rail, so a 5 V single supply board has to keep signals between roughly 0.8 V and 3 V.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.