Contact Us

TL064CDR

Brand: Texas Instruments
Texas Instruments TL064CDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL064CDR — Power Management & Signal Chain | Superb Automation

TL064CDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL064CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL064CDR: quad low power JFET input operational amplifier in a 14 pin SOIC body

TL064CDR is four of the 250 microamp JFET amplifiers on one die, giving 1 MHz of gain bandwidth per channel for about 1 milliamp of total supply current in a SOIC body of 14 pins. The D suffix in a 14 pin body is the quad version of the family, and the electrical table is the same per amplifier: 200 microamps typical and 250 microamps maximum, 1 MHz gain bandwidth, 3.5 V per microsecond slew, 15 mV maximum offset at 25 C and 30 nanovolts per root hertz of noise. Four amplifiers at the maximum column is a 1 milliamp package, which is the reason this part exists.

Order code and package

Order codeTL064CDR
Functionquad JFET input operational amplifier
PackageSOIC, 14 pins, body code D
Supply current200 microamps typical, 250 microamps maximum per amplifier
Package currentabout 1 milliamp with four amplifiers active
Gain bandwidth1 MHz per amplifier
Slew rate3.5 volts per microsecond
Channel separation120 dB
Temperature range0 to 70 C, C suffix
Input resistance10 to the 12 ohms
Output swingplus or minus 12 V typical into 10 kilohms
DatasheetSLOS081, low power JFET input family

Electrical parameters that decide the application

Offset voltage3 mV typical, 15 mV maximum at 25 C
Offset drift10 microvolts per degree
Input bias current30 picoamps typical, 200 picoamps maximum
Voltage noise30 nanovolts per root hertz at 1 kHz
Common-mode rejection70 dB minimum, 86 dB typical
Supply rejection70 dB minimum, 95 dB typical
Common-mode rangeplus or minus 11 V typical on 15 V rails
Output swing into 2 kilohmsplus or minus 10 V minimum on 15 V rails
Thermal resistance14 pin SOIC, lead frame path
Package dissipation4 times the single amplifier figure plus output load
Crosstalk120 dB at dc, falling with frequency
Pinoutstandard quad, 14 pins

Points to check before this part goes on a BOM

Four amplifiers in a 14 pin SOIC means the die runs warmer than a single. Each amplifier dissipates 7.5 milliwatts at the maximum supply current, so the package dissipates 30 milliwatts before any output current, and a 14 pin SOIC has a junction to ambient resistance around 100 C per watt, which is 3 degrees of rise. Only when the outputs drive loads does the package temperature become a limiting question.

A quad shares one pair of supply pins across four amplifiers, so the supply impedance is common to all four channels. With 120 dB of separation at dc and four channels switching, the practical crosstalk is set by the decoupling network: one capacitor at the package with a short ground return is worth more than any specification on the data sheet.

The 15 mV offset is per amplifier and independent between the four. Four channels on the same board therefore show a spread of up to 30 mV peak to peak, which for a four channel ratiometric measurement means each channel needs its own calibration rather than a single board level trim.

Power supply rejection of 70 dB minimum is what protects a four channel board from its own digital section. A 100 mV of switching ripple on the 15 V rail becomes 32 microvolts at the output, which is small next to the 15 mV offset, but at 1 MHz the rejection falls and the ripple appears directly in the channel that shares the supply.

The output stage on a 14 pin package has the same resistive current limit as the single, so a fault on one channel pulls the shared supply down and takes the other three with it. Fusing or series resistors on each output are the usual way to keep one sensor fault from disabling a four channel card.

This part is stable at unity gain with no external compensation, which is why it appears in Sallen and Key filters. The 1 MHz gain bandwidth limits the usable corner to roughly 50 kHz for a two pole stage with a Q of 1, so a four pole 100 kHz filter built from two stages will show more attenuation at the corner than the component values predict.

Where this order code fits

Four channel battery instruments, multi pole active filters, and boards that need a buffer per sensor input use this part. It is also the standard choice for a four channel transducer front end where each channel is slow and the total supply budget is fixed at a milliamp. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Why use a quad instead of four singles? Board area, supply decoupling and cost. One 14 pin package replaces four 8 pin packages and shares the supply pins, at the cost of a common supply impedance and a common thermal path.

Is the TL064 a drop in for the TL084? Same pinout and same supply range, but the bandwidth falls from 3 MHz to 1 MHz and the slew rate from 20 to 3.5 V per microsecond. Slow filters and dc amplifiers accept the swap; anything above 50 kHz does not.

What is the total supply current with four channels loaded? One milliamp for the amplifiers at the maximum column, plus the load current. Four channels driving 1 V into 10 kilohms adds 400 microamps, so the package budget becomes 1.4 milliamps.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.