Contact Us

TL062CDR

Brand: Texas Instruments
Texas Instruments TL062CDR is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TL062CDR — Power Management & Signal Chain | Superb Automation

TL062CDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TL062CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TL062CDR: dual low power JFET input operational amplifier in an 8 pin SOIC body

TL062CDR is two of the 250 microamp JFET amplifiers in one package, with 120 dB of separation between the halves and the same 1 MHz gain bandwidth in a SOIC body of 8 pins. The C suffix is the 0 to 70 C commercial grade, which is the grade most battery instruments use, and it costs nothing in the electrical table except the temperature window. Two amplifiers at 250 microamps maximum each means a 500 microamp package budget, and the pair shares one set of supply pins, so the decoupling and the ground return are per package rather than per amplifier.

Order code and package

Order codeTL062CDR
Functiondual JFET input operational amplifier
PackageSOIC, 8 pins, body code D
Supply current200 microamps typical, 250 microamps maximum per amplifier
Package currentabout 500 microamps with both amplifiers active
Gain bandwidth1 MHz per amplifier
Slew rate3.5 volts per microsecond
Channel separation120 dB
Temperature range0 to 70 C, C suffix
Input resistance10 to the 12 ohms
Output swingplus or minus 12 V typical into 10 kilohms on 15 V rails
DatasheetSLOS081, low power JFET input family

Electrical parameters that decide the application

Offset voltage3 mV typical, 15 mV maximum at 25 C
Offset drift10 microvolts per degree
Input bias current30 picoamps typical, 200 picoamps maximum
Bias current over temperature7 nanoamps at the full range limit
Voltage noise30 nanovolts per root hertz at 1 kHz
Common-mode rejection70 dB minimum, 86 dB typical
Supply rejection70 dB minimum, 95 dB typical
Supply rangeplus or minus 4.5 V to plus or minus 18 V, 36 V total
Output currentshort circuit protected by the output stage resistance
Gain bandwidth product1 MHz, unity gain stable
Crosstalk mechanismshared supply pins and die substrate
Package8 pin SOIC, two amplifiers

Points to check before this part goes on a BOM

Two amplifiers in one body share the supply pins, and that is where crosstalk comes from even with 120 dB of separation. A large signal on one half draws current through the shared bond wires and the supply impedance, and the second half sees that as a supply modulation. Local decoupling at the package pins is what keeps the 120 dB figure meaningful.

The zero to 70 C grade is not a limitation for indoor instruments and is a limitation for anything that goes outdoors. Below 0 C the JFET input stage and the bias network are outside specification, and while the part will usually work, the offset and bias current are not guaranteed over that range.

Supply current per amplifier matters more than the headline here because the pair is usually both active. Two amplifiers at 250 microamps maximum is 500 microamps, and a board that budgeted 250 microamps for the package doubles its supply drain with no change in the circuit diagram.

Offset of 15 mV maximum and drift of 10 microvolts per degree together give 16.75 mV over the commercial window, so the offset barely changes with temperature and the room temperature number is a fair estimate. That is unusual and it makes this family easy to calibrate once at production test.

The 1 MHz gain bandwidth with 3.5 V per microsecond slew means a two pole filter built around the pair runs out of loop gain well before the filter corner if the corner is above a few tens of kilohertz. A Sallen and Key stage with a 50 kHz corner and a Q of 5 wants far more gain bandwidth than 1 MHz, and the measured response will show it.

The output stage has a resistive short circuit limit rather than an active current limit, so a shorted output pulls the supply down through the output resistance instead of folding back. On a battery supply with a limited current capability that is a survivable condition; on a bench supply set to 100 mA it means the rail collapses and the other channel stops working.

Where this order code fits

Portable monitors use the pair as a two stage signal chain, an instrumentation amplifier front end, or a filter with two poles. The low supply current also makes it a fit for battery backed sensor boards that stay powered while the main processor sleeps, and the JFET input suits the high impedance divider networks those boards use. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Are the two amplifiers in the TL062 independent? Electrically yes, with 120 dB of separation, but they share supply pins and the substrate. A large signal on one half modulates the supply of the other unless each supply pin is decoupled locally.

Can this replace a TL072 in an existing board? The pinout is the same and the supply range is the same, but the bandwidth drops from 3 MHz to 1 MHz and the slew rate from 20 to 3.5 V per microsecond. It is a drop in for slow circuits and a rebuild for anything above a few tens of kilohertz.

What supply current should be budgeted? 500 microamps for the package at the maximum column, with both amplifiers active and no load. Adding a 10 kilohm load at 1 V adds 100 microamps per channel.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.