THS6093IPWP
Product Specifications
THS6093IPWP
Texas Instruments — Power Management & Signal Chain
Product Overview
The THS6093IPWP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
THS6093IPWP: single supply xDSL line driver with shutdown in a 20 pin PowerPAD HTSSOP
THS6093IPWP is the same single supply driver as the THS6092 with a shutdown input referenced to the mid rail, in the thermally enhanced PWP body in a HTSSOP body of 20 pins. The shutdown logic on this part is referenced to the mid rail rather than to ground, which is why the data sheet writes it with the reference pin at 6 V and the shutdown pin at 8 V: the threshold follows the split point of the supply, so a single supply board does not need a level shifter. The PWP body carries the PowerPAD, and the electrical table is the 6092 table with the standby block added.
Order code and package
| Order code | THS6093IPWP |
| Function | dual single supply line driver with shutdown |
| Package | HTSSOP, 20 pins, PowerPAD, body code PWP |
| Supply range | single supply, specified at 12 V and at 5 V |
| Bandwidth | 100 MHz at 12 V, 90 MHz at 5 V |
| Slew rate | 600 volts per microsecond at 12 V, 400 at 5 V |
| Output swing | 1.9 to 10.1 V at 12 V rails |
| Shutdown reference | referenced to the mid rail, 8 V on a 6 V reference |
| Standby current | shutdown pin holds the driver off |
| Output current | 325 mA short circuit |
| Enable and disable | specified in the shutdown characteristics table |
| Junction range | minus 40 to plus 85 C, I suffix |
Electrical parameters that decide the application
| Differential offset | 1 mV typical, 6 mV maximum |
| Single ended offset | 6 mV typical, 16 mV maximum |
| Bias current | 3 microamps typical, 10 microamps maximum |
| Voltage noise | 2.1 nanovolts per root hertz at 10 kHz |
| Third order distortion | minus 70 dBc at 2 V peak to peak |
| Crosstalk | minus 65 dBc at 1 MHz on 5 V |
| Output current | 325 mA short circuit |
| Input common mode | 1.5 to 3.5 V at 12 V, 1.1 to 3.9 V at 5 V |
| Thermal path | PowerPAD on the package underside |
| Logic levels | referred to the mid rail, not to ground |
| Package | HTSSOP, 20 pins |
| Datasheet | SLOS313 family, shutdown table for the 6093 |
Points to check before this part goes on a BOM
The shutdown threshold moves with the supply. With the reference pin at 6 V the power down level is 8 V, so a controller that drives the pin from ground referenced logic has to add the mid rail offset. This is the single most common wiring mistake on this part, and it shows up as a driver that never turns off.
The 20 pin PWP package is larger than the 8 pin SOIC of the 6092 for a reason: the PowerPAD gives the die a thermal path that the SOIC lead frame does not. On a 12 V rail with 325 mA of fault current the difference between the two bodies is the difference between a part that survives a fault and one that does not.
Everything in the analogue table is the 6092 table. Offset of 16 mV maximum single ended, 6 mV differential, 2.1 nanovolts per root hertz and minus 70 dBc at 2 V peak to peak all carry over, so a board moving from 6092 to 6093 changes the package and the logic reference, not the signal path.
Single supply biasing puts the quiescent output at mid rail, which halves the available swing in each direction. On 12 V that is 1.9 to 10.1 V, an 8.2 V window; the transformer then sees 16.4 V peak to peak single ended and twice that differentially, and any offset shift from bias current eats into the smaller of the two margins.
Bias current of 10 microamps through the feedback network shifts the quiescent point, and on a single supply that shift is not symmetric: it reduces headroom on one side while adding it on the other. A 7.5 mV shift on an 8.2 V window is small, but it compounds with the 16 mV offset limit on the same node.
The 5 V column is a separate specification, not a derating. Slew rate falls to 400 V per microsecond, the input window widens to 1.1 to 3.9 V, and the output window becomes roughly 1.4 to 3.9 V, which is about 5 V peak to peak differential. A board qualified at 12 V cannot be moved to 5 V without re-measuring distortion at the lower amplitude.
Where this order code fits
Customer premises equipment with per port power management uses this part, particularly where the modem has to mute its transmitter while the line is being trained or while the subscriber is idle. The PowerPAD body also makes it the choice when the same board has to drive a short loop at high current continuously. Boards comparing it with a neighbouring part start from our How to Verify a Drop in Replacement page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Why does the shutdown pin need a mid rail reference? Because the driver's internal bias sits at mid rail on a single supply, so the logic comparator is referenced there. Driving the pin from ground referenced logic gives a threshold that is 6 V away from where the comparator expects it.
Is the THS6093IPWP pin compatible with the THS6092ID? No. The 6092 is an 8 pin SOIC and the 6093 is a 20 pin HTSSOP with a PowerPAD, so the footprint changes and the thermal pad has to be soldered to a copper plane.
Does the part draw any current in shutdown? The shutdown block reduces the driver to a standby state rather than to zero. The bias network and the reference stay alive, so the standby current is a small but non-zero figure from the shutdown characteristics table.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Amplifier Cross Reference page sets out the checks that keep a substitute from failing on the bench.