Contact Us

SN65MLVD206BDR

Brand: Texas Instruments
Texas Instruments SN65MLVD206BDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65MLVD206BDR — Power Management & Signal Chain | Superb Automation

SN65MLVD206BDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65MLVD206BDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65MLVD206BDR: a multipoint LVDS driver and receiver on one die

The SN65MLVD206BDR combines one M-LVDS driver and one M-LVDS receiver in an eight pin body. It meets the TIA/EIA-899 multipoint standard, which is the multipoint companion to the point to point TIA/EIA-644 standard: the driver is sized for a bus loaded by terminations at both ends, and the receiver thresholds are defined for a bus that may be idle, open or driven by another card.

The receiver comes in two threshold flavours across the family. The Type-1 receiver has 25 mV of hysteresis so that a slowly changing or lightly driven input does not produce output chatter. The Type-2 receiver adds a 100 mV offset, which gives a defined output when the bus is open or idle. The common mode range is minus 1 V to 3.4 V, which allows 2 V of ground noise between cards, and the part powers up and down without glitching the bus.

Key data for the SN65MLVD206BDR

FunctionOne M-LVDS driver plus one receiver on a shared pair, half duplex at the bus level
StandardTIA/EIA-899 multipoint LVDS, with 30 ohm to 55 ohm load capability
RateUp to 200 Mbps signalling rate
ReceiverType-1 25 mV hysteresis, Type-2 100 mV offset for open and idle bus detection
Common modeMinus 1 V to 3.4 V, which tolerates about 2 V of ground difference between cards
BehaviourGlitch free power up and power down, high impedance bus pins when disabled or unpowered

Body, marking and reel data

BodySOIC D, 8 pins, 4.9 mm by 3.91 mm
Reel2500 pieces on a large reel on the rows that print a quantity, 75 pieces in a tube on the D rows
MarkingMF206 printed on the body
HandlingMoisture level 1, 260 C peak, unlimited floor life
TemperatureMinus 40 C to 85 C

Half duplex multipoint in a small cabinet

A rack that distributes a serial control bus to eight cards can use this part at every node. Each card drives the pair when it is polled, and listens the rest of the time. The 200 Mbps rate is far above what a control protocol needs, which leaves room for a shared clock or a burst of configuration data, and the multipoint driver rating means the swing does not sag as cards are added.

The Type-2 receiver is what makes an idle bus safe. With no card driving, a plain receiver may settle at either state and the controller sees random start bits. The 100 mV offset forces a known output, so the protocol can treat an idle line as a mark state without adding bias resistors to every card.

Questions a buyer should ask about this string

The first is the B in the part number. The orderable table in this revision prints SN65MLVD206DR as the reel row, at 2500 pieces with a Level-1 rating and a marking of MF206, and it does not print a BDR row. The B version is released under its own document with its own electricals, so a line that specifies the B should confirm the vendor acknowledgement rather than assume the base row covers it.

The second is the receiver type. The Type-1 and Type-2 thresholds are not interchangeable in a protocol that relies on idle bus detection, and the ordering information separates them by part number rather than by a suffix letter that is obvious from the title.

What to ask before quoting this transceiver

The first question is the receiver type. A Type-1 receiver with 25 mV of hysteresis suits a bus that is always driven, and a Type-2 receiver with a 100 mV offset suits a bus that can go idle. The two are different part numbers, and a protocol that expects one and gets the other will see framing errors at the end of every transaction.

The second question is the part number revision. The orderable table in this revision prints the base row at 2500 pieces with a Level-1 rating and an MF206 marking, and it does not print the B row that this catalogue entry names. We confirm the revision against the vendor acknowledgement before the order is placed, and where the B revision is required we quote from its own document rather than from this one.

The third is the termination. Two resistors are still required on a multipoint bus, and their value should match the cable rather than the 100 ohm of a point to point link. Where the bus crosses between cabinets, the surge and grounding question is covered on our incoming inspection plan page for the goods side, and the second source route for interface parts is on our second source page.We also ask whether the card is hot plugged, because the glitch free power up and power down behaviour of this family is only useful if the enable timing on the card respects it, and a card that drives the bus before its supply is stable will still disturb the segment.