SN65LVDS84AQDGGRQ1
Product Specifications
SN65LVDS84AQDGGRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65LVDS84AQDGGRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65LVDS84AQDGGRQ1: a 21 bit FlatLink transmitter for an LCD panel
The SN65LVDS84AQDGGRQ1 is a FlatLink transmitter that takes 21 parallel data bits plus a clock and compresses them into three LVDS data pairs plus one clock pair. The compression is 21 to 3, and the throughput is 196 million bytes per second, which is enough for SVGA, XGA and SXGA panels. The parallel side runs on low voltage TTL levels and the serial side on LVDS, so a processor with a wide display bus drives a thin cable to the panel.
The part runs from a single 3.3 V supply and dissipates 89 mW typical, against about three times that for the older SN75LVDS84 it replaces. Disabled, it draws less than 0.54 mW. The phase lock loop locks over a 31 MHz to 75 MHz input range with no external components, and it tracks a spread spectrum clock with 3 per cent centre spread at 50 kHz modulation, which is what allows a panel link to pass an emissions test without shielding the flex.
Key data for the SN65LVDS84AQDGGRQ1
| Function | 21 to 3 channel compression, 21 data bits plus clock in, three data pairs plus clock out |
| Throughput | 196 million bytes per second, suited to SVGA, XGA and SXGA panel timing |
| Clock | Phase lock input range 31 MHz to 75 MHz, no external components needed for the loop |
| Supply | 3.3 V single rail, 89 mW typical, below 0.54 mW when disabled |
| Outputs | LVDS pairs meeting ANSI EIA/TIA-644, low EMI by construction of the differential pair |
| Spread spectrum | Tracks 3 per cent centre spread at 50 kHz modulation frequency |
Body, marking and reel data
| Body | TSSOP DGG, 48 pins, 20 mil lead pitch |
| Reel | 2000 pieces on a large reel on the DGGR rows, 40 pieces in a tube on the DGG rows |
| Marking | 65LVDS84AQ printed on the automotive qualified die |
| Handling | Moisture level 2, 260 C peak, one year floor life |
| Temperature | Minus 40 C to 125 C on the qualified row, while the .A row of the same string prints 0 C to 70 C |
Why the panel side of an instrument still uses this part
A medical monitor, a test instrument front panel or an automotive cluster all need to move a wide pixel bus across a hinge or a flexible cable. Sending 21 lines plus a clock across that cable needs 22 conductors, a wide connector and a lot of ground returns. The transmitter cuts it to four pairs, which is eight conductors, and the differential signalling keeps the emissions low enough that the flex does not need a shield.
The other reason is the lock range. A 31 MHz to 75 MHz window covers the pixel clocks of the common panel resolutions, and because the loop needs no external components, the board has no loop filter to tune and no component tolerance to budget. The spread spectrum tracking then lets the system clock be modulated for emissions without unlocking the link.
What to check before this code is confirmed
The first check is the receiver at the far end. This is a transmitter, and the panel or the deserialiser has to match the mapping, which for this part is the SN65LVDS94 group and the equivalent FlatLink receivers. The second is the temperature row: the qualified part is minus 40 C to 125 C while the .A row prints 0 C to 70 C, and mixing them in one build creates two different thermal behaviours on the same line.
The third is the order string itself. The orderable table prints SN65LVDS84AQDGGR for the 2000 piece reel and SN65LVDS84AQDGG for the 40 piece tube, and neither row carries the Q1 suffix that the catalogue title uses. The Q is visible in the marking, so the suffix question can be settled from the reel label, but a purchase order that copies the catalogue title may not match a vendor acknowledgement line for line.
Panel link parts and the reel they arrive on
This transmitter is bought against a panel, so the quotation always names the panel resolution and the pixel clock. The 31 MHz to 75 MHz lock range covers the common resolutions, and a panel that needs a clock outside that window needs the other FlatLink member. We also ask whether the panel receiver is integrated or discrete, because that decides whether a separate deserialiser is on the order.
The packing is 2000 pieces on a large reel for the DGGR rows and 40 pieces in a tube for the DGG rows. A panel build that runs in batches takes the reel and keeps the tube for the prototype and the repair station. The automotive qualified die is marked 65LVDS84AQ, and the temperature window on that row reaches 125 C, which is what an instrument cluster or a head up display needs behind a windshield.
Where the code has to be matched against a panel driver that is being discontinued, the route is on our obsolete part cross reference hub. Where the build is a medical instrument and the traceability matters, our note is on our medical device components page.