Contact Us

SN65LVDM050PWR

Brand: Texas Instruments
Texas Instruments SN65LVDM050PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LVDM050PWR — Power Management & Signal Chain | Superb Automation

SN65LVDM050PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LVDM050PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LVDM050PWR: two full duplex LVDS channels on one 3.3 V rail

The SN65LVDM050PWR carries two independent driver and receiver pairs, each wired as a full duplex channel, in a 16 pin TSSOP. It belongs to the LVDM group rather than the plain LVDS group because the driver delivers more current: the output stage is sized for a doubly terminated bus, where both ends carry a 50 ohm resistor and the effective load seen by the driver is 50 ohm instead of the 100 ohm of a single termination.

The trade off is bandwidth for reach. With the heavier load the part runs at a typical full duplex signalling rate of 100 Mbps, not the 400 Mbps of the standard LVDS parts, and in exchange it drives a bus that stays properly terminated at both ends. Output swing is about 340 mV into that 50 ohm load, the bus terminals survive 12 kV of discharge, and the LVTTL inputs tolerate 5 V even though the supply is 3.3 V.

Key data for the SN65LVDM050PWR

ChannelsTwo full duplex channels, four drivers and four receivers in total
Rate100 Mbps typical full duplex signalling per channel
Load50 ohm effective, which is a bus terminated at both ends rather than at one end
Swing340 mV typical differential output into a 50 ohm load
DelaysDriver 1.7 ns typical, receiver 3.7 ns typical, with 50 mW and 60 mW dissipation at 200 MHz
Interface3.3 V supply, 5 V tolerant LVTTL inputs, 12 kV bus terminal ESD

Body, marking and reel data

BodyTSSOP PW, 16 pins, the 4.4 mm body used on dense backplane cards
Reel2000 pieces on a large reel on the plain, .B and G4 rows
MarkingLVDM050 on every reel row of this string
HandlingMoisture level 1, 260 C peak, unlimited floor life
TemperatureMinus 40 C to 85 C

Why double termination is worth the speed loss

A single terminated LVDS link reflects the far end of the cable back into the driver, and at a few hundred megabits the reflection lands inside the eye. Terminating both ends absorbs the reflection at the source, and the price is that the driver must supply twice the current for the same swing. That is exactly what this family does, and the reason a 100 Mbps link on a 20 metre backplane can be built with ordinary FR-4 and no equalisation.

The other use is multi-drop clock distribution inside a chassis, where a clock card feeds several boards along a backplane and the far end is terminated. In that configuration the driver sees the parallel combination of the branch impedances plus the terminations, and the 50 ohm rating is the number to work against rather than the ideal 100 ohm.

Questions we hear when this code is on a BOM

The first is whether the plain LVDS050 can be used instead. It can, if the bus is terminated at one end only, and then the 400 Mbps family is available at the same pin count. The second is about the disabled state: the driver goes high impedance when disabled, so a shared pair can be handed between two cards, and the receiver keeps a high input impedance when the supply is below 1.5 V, which is what protects a card that is powered down in a live shelf.

The third is about cable and connector choice. Because the swing is 340 mV and the load is 50 ohm, a connector with a poor ground return will show up as common mode noise rather than as amplitude loss, and the fix is a ground pin per pair rather than a bigger driver.

Matching the driver to the bus before the quote

Before we quote this code we ask two questions: is the bus terminated at one end or both ends, and how long is it. A doubly terminated bus is what this driver is rated for, and a single terminated link is better served by the standard LVDS family at the same pin count and a quarter of the current. Getting that wrong does not show up on a bench test with a short cable, and it does show up in the field as an eye that closes at temperature.

The second question is the connector. Two pairs plus a ground per pair is the minimum for a clean link at 100 Mbps, and a connector that shares one ground across four pairs will put the return current through the signal pair. We keep the 2000 piece reel in stock for this family because backplane projects tend to order in waves, and a wave that starts in one quarter usually repeats in the next.

Our sourcing note on interface parts and their second sources sits on the pin to pin cross reference page, and the way we hold a buffer for a long running backplane product is described on our safety stock planning page. Send the pair count and the length and we will quote the reel and the date code.