Contact Us

SN65LBC174A16DWR

Brand: Texas Instruments
Texas Instruments SN65LBC174A16DWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65LBC174A16DWR — Power Management & Signal Chain | Superb Automation

SN65LBC174A16DWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65LBC174A16DWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65LBC174A16DWR: quad RS-485 differential line driver with 11 ns propagation delay

SN65LBC174A16DWR is four differential line drivers in one 16 pin body, built for a parallel bus that needs several outputs switched together and a pinout that matches the older 75174 and MC3487 parts in a SOIC body of 16 pins. It drives four differential pairs at signalling rates up to 30 Mbps with propagation delays below 11 ns, a pulse skew of 2 ns maximum and an output skew of 2 ns, on a single 5 V supply, with 1.5 mA maximum standby current, 12 kV of output ESD protection, positive and negative current limiting on each driver, thermal shutdown, glitch free power up and power down, and two enable inputs that switch the four drivers in pairs or all together. The 16 pin body carries the standard 75174 pinout, so a board built around the older part can take this one without a copper change.

Order code and package

SN65LBC174A16DWRSOIC DW body, 16 pins, 10.3 mm by 10.3 mm, Active in the addendum dated 10 April 2024 revision, 2000 pieces on a large reel, moisture level printed as Call TI, minus 40 to plus 85 degrees, marking 65LBC174A
SN65LBC174A16DWthe tube row of the same 16 pin body, printed Obsolete, so a small build needs the reel or the 20 pin variant
SN65LBC174ADWRthe 20 pin body, also Active at 2000 pieces. It is not a drop in for the 16 pin part, and the extra pins carry a second set of enable and ground connections
SN75LBC174Athe commercial temperature version, 0 to 70 degrees, printed Obsolete in both the 16 and 20 pin bodies
Pin compatible partsthe vendor lists the SN75174, MC3487, DS96174, LTC487 and MAX3042 as the industry parts this pinout matches, which is the list to check when a customer is re sourcing an older board

Electrical parameters that decide the application

Supplya single 5 V rail, which is what the installed base of parallel bus boards runs on
Signalling rateup to 30 Mbps, with propagation delays below 11 ns and 5.5 ns typical, which is fast enough for a backplane with several cards
Skewa pulse skew of 0.6 ns typical and 2 ns maximum, and an output skew of 2 ns, which is the figure that decides whether a parallel bus closes its timing at the far end
Drivefour differential outputs, each with positive and negative current limiting so a shorted pair pulls a bounded current rather than the rail
Output swinga steady state differential output of at least 1.5 V into 54 ohm, the standard RS-485 test load, with a change of no more than 0.1 V between the two states
Standby current1.5 mA maximum with the drivers disabled, so a card that is not transmitting costs almost nothing
ESD12 kV on the driver outputs, the vendor figure for this family
Enablestwo enable inputs, one per pair of drivers, which can be tied together to switch all four with one signal
Fail behaviourwhen disabled or unpowered, the outputs present a high impedance to the bus so a card that is removed does not load the pair
Thermal shutdownan internal junction limit that protects the drivers during a sustained fault
StandardsTIA/EIA-485, TIA/EIA-422 and ISO 8482 are named, with the footnote that the minimum output may not fully comply with TIA/EIA-485-A below 0 degrees
Temperatureminus 40 to plus 85 degrees on the printed rows of this string

Family variants and how they differ

174A against 174the A revision is the current die with the same pinout. A substitution between them changes the differential output margin, so the timing and the swing should be checked on the bus rather than assumed
16 pin against 20 pinthe 16 pin body is the 75174 outline and the 20 pin body is the wider variant with extra enable and ground pins. They are not interchangeable on an existing board
Against a transceiverthe 174A is a driver only and has no receiver. A bidirectional port needs a receiver, either a separate part or a transceiver such as the LBC176
Against a modern 3.3 V quad drivera 3.3 V part removes one rail and one level shifter, and needs a board change. The 174A is chosen when the 5 V backplane and the 75174 footprint are fixed
Against an isolated driveran isolated part puts a barrier on each pair and needs an isolated supply. A backplane inside one rack does not need it

Points to check before this part goes on a BOM

The cold temperature footnote appears on this driver as well as on the LBC176 receiver: the minimum differential output may not fully comply with TIA/EIA-485-A at operating temperatures below 0 degrees. A backplane that has to meet the standard at minus 40 needs a cold chamber measurement of the actual bus, not a reading of the feature list.

The skew numbers are the reason a parallel bus can still close timing with a 1990s part. A 2 ns output skew across four drivers and a 0.6 ns typical pulse skew are better than many modern parts, and replacing this device with a cheaper quad driver usually shows up as a timing failure at the far end of the backplane rather than as a gross functional fault.

The 16 pin and 20 pin bodies are two different boards. The 20 pin variant carries a second enable and additional ground pins, and a customer who orders the 20 pin part to replace a 16 pin one will find the footprint does not fit. The suffix 16 in the orderable string is the marker of the 16 pin body and it is worth reading literally.

The 12 kV output ESD rating is lower than the 15 kV on the transceiver families and it applies to the driver outputs. A backplane connector that is handled during service can put more than that on a pin, and the external protection on the card is what absorbs the difference. The rating is a pin figure, not a system figure.

The 1.5 mA standby current is the figure with the drivers disabled, which is the normal state of a bus card that is not transmitting. A card that keeps all four drivers enabled to hold a defined level on the pair draws the operating current and heats the package, and the datasheet power dissipation rows apply.

This part has no receiver and no fail safe bias. A bus that needs a defined idle level needs the bias network and a receiver, and the fault behaviour of an idle pair belongs to those parts. A customer who reports a bus that floats when this card is removed is describing the missing receiver, not a driver fault.

Where four drivers share one package

A parallel backplane carries address, data and control as separate differential pairs, and each pair needs a driver. Four in one package keeps the skew between the pairs defined by one die and one temperature, which is something four separate parts cannot promise. That is the reason this part exists next to the single transceiver families.

The cost is that all four drivers share a supply pin and a thermal path. One shorted pair heats the whole package and the thermal shutdown turns off the other three as well, so a fault on one line takes the card off the bus. A board that needs per pair isolation uses separate parts.

What the order code decides

The string reads SN65LBC174A for the device, 16 for the 16 pin body, DW for the wide SOIC and R for the large reel of 2000. The 20 pin body drops the 16 and adds the extra pins. The 75 prefix is the commercial temperature grade and it is printed Obsolete in both bodies, so the industrial 65 string is the one in production.

Where this order code fits

Motor drives, factory automation and control, and parallel backplanes in noisy environments are the applications the vendor prints, and a card that has to drive four differential pairs with matched timing is the case this part is bought for. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Is SN65LBC174A16DWR a transceiver? No. It is a quadruple differential line driver with no receiver. A bidirectional port needs a receiver as well.

What is the propagation delay? 5.5 ns typical and 11 ns maximum, with 0.6 ns typical pulse skew and 2 ns output skew across the four drivers.

Is the 20 pin version a drop in replacement? No. The 20 pin body carries extra enable and ground pins and needs a different footprint.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.