Contact Us

SN65HVDA195QDRQ1

Brand: Texas Instruments
Texas Instruments SN65HVDA195QDRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVDA195QDRQ1 — Power Management & Signal Chain | Superb Automation

SN65HVDA195QDRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVDA195QDRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVDA195QDRQ1: automotive LIN physical interface with wake up and inhibit control

SN65HVDA195QDRQ1 is a LIN 2.0 physical layer transceiver with wake up and a regulator inhibit output in a SOIC body of 8 pins. It is the single wire interface between a LIN bus and a microcontroller, with an internal pull up resistor and series diode for responder nodes, a wake up input and an inhibit output that controls the external regulator. The DRQ1 order code is the 8-pin SOIC in the automotive grade reel.

Order code and package

Order codeSN65HVDA195QDRQ1
Package8-pin SOIC, D body, 4.90 mm by 3.91 mm
Packingtape and reel, automotive grade
PinsRXD, EN, NWake, TXD, GND, LIN, VSUP, INH
ProtocolLIN 2.0 and SAE J2602, 20 kbit/s maximum
Bussingle wire, bidirectional, dominated by the bus voltage
Wake upbus wake up, NWake input, and the EN pin

Electrical parameters that decide the application

Supply7 V to 27 V operating on VSUP, 40 V absolute maximum
Bus voltageminus 40 V to plus 40 V on the LIN pin
ESD on LINplus or minus 12 kV HBM
Sleep currentabout 20 microampere with wake up circuits still live
Under voltage threshold4.8 V to 6 V on VSUP
Logic levels3.3 V and 5 V microcontroller compatible
Bus rate20 kbit/s LIN, and down to 0 baud in MOST ECL mode
Protectionshort to battery and short to ground on the bus, thermal, loss of ground

Family variants and how they differ

SN65HVDA195-Q1the automotive qualified part with the inhibit output
Responder nodesuse the internal pull up and series diode, no external parts
Commander nodesneed an external 1 kohm pull up and a series diode per the LIN spec
Q1 suffixthe automotive qualification and the reel marking

Points to check before this part goes on a BOM

LIN is a single wire bus, so the ground return is part of the channel. A node that shares its ground with a motor or a relay driver sees the bus reference move by volts, and the LIN pin rating of minus 40 V to plus 40 V is what keeps that from destroying the part. It does not keep the data intact, so the ground topology still has to be planned.

The part has no dominant state timeout, which is why the data sheet can claim operation down to zero baud. A frame that begins and never ends leaves the bus held dominant, and the protocol layer in the controller has to enforce the timeout. A node that relies on the transceiver to release the bus will hold it until the watchdog resets the controller.

Responder nodes can use the internal pull up and series diode, so a sensor with a single wire and a ground needs no external components on the bus. Commander nodes cannot: the LIN specification requires a 1 kohm pull up to the battery rail plus a series diode, because the commander has to pull the bus low against the responder pull ups and its own diode has to block the battery when the ignition is off.

The INH output controls the external regulator. It goes active when the part wakes and stays active while the node is running, which lets a sleeping module keep its microcontroller supply off entirely. A board that ties INH to the enable of a regulator and also feeds the regulator output back into the part has to make sure the part is supplied from the battery rail rather than from that regulator.

Sleep current of about 20 microampere in the 7 V to 12 V battery range is what keeps a parked vehicle module inside its quiescent budget. The wake up path stays live at that current, so a bus transition, an edge on NWake or the EN pin brings the node back. The 20 microampere figure is at 95 degrees junction and doubles at higher temperature in the table.

The under voltage threshold between 4.8 V and 6 V protects the bus during a crank. Below that window the part turns its output off and the node stops driving the bus, which is the behaviour a start stop vehicle needs: the module must not hold the bus dominant while the battery rail collapses to 6 V during a cold crank.

The 12 kV HBM rating on the LIN pin covers handling and connector discharge, and the part also survives the ISO 7637 transient set. Those are the waveforms a vehicle harness produces, and they are not the same as an IEC surge on a factory cable. A LIN port that leaves the enclosure still needs the connector level protection the harness specification calls for.

Logic compatibility covers both 3.3 V and 5 V microcontrollers through the same pins, and RXD is an open drain output that reports the bus state. Because RXD is open drain, it needs a pull up on the board, and the value of that pull up sets the edge rate that the controller sees. A 100 kohm pull up with a long trace gives a slow edge that some UARTs sample badly.

The bus load in the electrical table is a 500 ohm pull up with 10 nF of capacitance, which is the LIN specification load. A harness with more capacitance than that slows the edges and narrows the sampling window, and the 20 kbit/s rate is slow enough that the limit is usually the pull up not the capacitance.

The TXD input is the only way to hold the bus dominant, and the part has no internal timeout on it. A microcontroller that stops clocking with TXD low leaves the whole bus dominant and every other node unable to speak. That is why LIN controllers carry a timeout on the transmit path and why the part is specified to work down to zero baud rather than to protect against it.

INH is intended to hold an external regulator on while the node is awake. A board that powers the transceiver from that same regulator has no way to wake, because the part is unpowered when the regulator is off. The supply pin has to sit on the battery rail through a reverse blocking diode, which is exactly what the pin description says.

The LIN pin includes the series diode and the pull up for a responder node, and it also blocks back feed into the supply when the battery is disconnected. A node that adds its own external diode in series duplicates that block and shifts the recessive level, which changes the recessive to dominant margin at the far end of the bus.

Where this order code fits

It is used in body control modules, door and seat modules, sensor nodes and small actuators where a single wire network has to wake a sleeping module. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Is this a CAN transceiver? No. It is a LIN physical interface, single wire, 20 kbit/s, with an inhibit output for a regulator. CAN needs a differential pair and a different part.

What does the Q1 suffix mean? It marks the automotive qualified version, screened and reeled for vehicle assembly. The electrical behaviour is the same as the non Q1 part.

Can INH drive a regulator directly? INH is a logic level output intended for the enable pin of a regulator. It is not a switch: it sources no load current and cannot be used to gate a relay coil or a lamp.

Does the part need an external diode on a responder node? No. The internal series diode and pull up are enough for a responder. A commander node needs the external 1 kohm pull up and diode that the LIN specification requires.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.