Contact Us

SN65HVD70DR

Brand: Texas Instruments
Texas Instruments SN65HVD70DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD70DR — Power Management & Signal Chain | Superb Automation

SN65HVD70DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD70DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD70DR: 3.3 V full duplex RS-485 transceiver at 400 kbps with 30 kV bus protection

SN65HVD70DR is a four wire differential driver and receiver on 3.3 V, with separate input and output pins so a link can send and receive at the same time, and a bus protection level that survives a direct discharge to the pins in a SOIC body of 14 pins. It runs at 400 kbps with a 1/8 unit load that allows up to 256 nodes, more than plus or minus 30 kV human body model, more than plus or minus 12 kV IEC 61000-4-2 contact discharge and more than plus or minus 4 kV fast transient burst on the bus pins, 70 mV of receiver hysteresis, under 1.1 mA quiescent, 10 nA typical standby with a 5 uA maximum, and it is specified from minus 40 to plus 125 degrees. The SOIC body is 14 pins because the driver and receiver each need their own pair, which is the physical difference between full duplex and the two wire parts.

Order code and package

SN65HVD70DRSOIC D body, 14 pins, 8.65 mm by 3.91 mm, Active in the addendum dated 10 August 2026, 2500 pieces on a large reel, NIPDAUAG finish, moisture level 2 with a one year floor life, minus 40 to plus 125 degrees, marking HVD70
SN65HVD70DGSRthe 10 pin VSSOP body, 3 mm by 3 mm, 2500 on a large reel, the same moisture level 2 with a one year floor life, for a board that cannot carry the 14 pin outline
SN65HVD70D and DGSthe tube rows, 50 pieces in the SOIC and 80 in the VSSOP, which is where a prototype order comes from
SN65HVD71, 74 and 77the same silicon with no enable pins, fully on all the time. A point to point link that never needs to release the bus takes one of these and saves two control lines
SN65HVD73 and 76the 20 Mbps and 50 Mbps full duplex members with the same enable scheme, for a short link that has to move more data than 400 kbps

Electrical parameters that decide the application

Supplya single 3.3 V rail with 5 V tolerant logic inputs, so the port works behind either controller family
Signalling rate400 kbps on this member, with 20 Mbps and 50 Mbps siblings in the same family for a short, terminated link
Duplexfull duplex, four wires, separate driver outputs and receiver inputs, so the link can transmit and receive at once instead of turning the pair around
Node countup to 256 nodes at 1/8 unit load, which is the highest count in the family and the reason a multidrop full duplex bus is possible at all
ESDmore than plus or minus 30 kV human body model, more than plus or minus 12 kV IEC 61000-4-2 contact and more than plus or minus 4 kV fast transient burst, all on the bus pins
Hysteresis70 mV of receiver hysteresis, slightly less than the 80 mV of the half duplex family and still wide enough for a long, attenuated pair
Quiescent currentunder 1.1 mA operating, and 10 nA typical in standby with a 5 uA maximum, so a listening node costs almost nothing
Enablesthe 70 has an active high driver enable and an active low receiver enable, so the controller can park one direction without touching the other
Moisture levellevel 2 with a one year floor life, not level 1, so a reel that has been open for more than a year needs a bake before reflow
Fail safedefined receiver output on an open, shorted or idle bus, and glitch free power up and power down for hot plugging
Common modethe wide window the family is specified over, enough for a long run with a ground difference between the two ends
Temperatureminus 40 to plus 125 degrees on every printed row, and the electrical table is written across that full range

Family variants and how they differ

70 against 71same silicon, the 71 is fully enabled with no control pins. A point to point link that is always on takes the 71 and saves two traces
70 against 73the 73 is the 20 Mbps member with the same enables, for a shorter link that needs more bandwidth. The cable has to support it
70 against the half duplex 72the 72 is two wires and 250 kbps. Full duplex doubles the wire count and removes the turnaround time, which matters when the protocol has to answer inside a fixed slot
Against an isolated full duplex partan ISO1450 class device puts a barrier on the four wire port and needs an isolated supply. A link between two cabinets usually needs it, a link inside one does not
Against a discrete driver and receiver pairtwo separate parts cost more board area and two more part numbers, and the enable timing between them is not specified as a pair. One package removes that coordination problem

Points to check before this part goes on a BOM

Full duplex means four wires and a 14 pin body, and that is a cable decision as much as a silicon one. A customer who replaces a two wire part with this one and keeps the existing pair will find that the link no longer works, because the receiver inputs are on separate pins from the driver outputs and the pair is not shared.

The moisture level on this row is 2 with a one year floor life, which is worse than the level 1 of the half duplex family and is a consequence of the larger body. A contract assembly house has to write that floor life onto the process card, and a reel that sat open over a shutdown needs a bake. This is the kind of difference that shows up as popcorning on the first build after a holiday.

The 30 kV human body model rating is double the 15 kV of the half duplex family, and it is printed as a bus pin rating. What it does not cover is a surge on the cable from a nearby lightning strike, which is a different test with a different waveform and belongs to the external protection rather than to the transceiver.

The 256 node count comes from the 1/8 unit load and it assumes the bus is terminated once at each end regardless of node count. Adding termination at every node is a common field error and it loads the driver until the differential output falls below the standard minimum. The number on the data sheet is a receiver loading figure, not a licence to terminate everywhere.

The 10 nA standby figure is only reached with both enables parked in the standby state, and the 5 uA maximum is the number to use for a budget rather than the typical. A product that holds a full duplex port listening cannot use the standby figure at all, because the receiver is active and the part draws its operating current.

The enable pins behave differently on the two directions: the driver enable is active high and the receiver enable is active low. Boards that wire both to one controller pin usually work on the bench and fail when the firmware drives that pin high during a transmit, because the receiver turns off at the same time and the node stops hearing the reply.

Where four wires pay for themselves

A protocol that has to answer inside a fixed time slot cannot afford the turnaround delay of a two wire bus, and a full duplex link removes that delay entirely. The same argument applies to a multidrop bus where one master polls many nodes and the replies overlap with the next request.

The cost is a second pair, a 14 pin body and a cable with four conductors and a shield. On a new installation that is a drawing change; on a retrofit it is a re cable, which is why most installed RS-485 links stay half duplex even where the protocol would benefit.

What the order code decides

The string reads SN65HVD70 for the device, DR for the SOIC body and no suffix letter after it, or DGSR for the 10 pin VSSOP. The rate and the enable scheme are set by the device number, and the package decides whether the board needs 14 pins or 10. Both rows print 2500 on a large reel and both carry moisture level 2 with a one year floor life.

Where this order code fits

E-meters, industrial automation and building automation are the applications the vendor prints, and a link where the master polls a node and needs the answer inside the same cycle is where a four wire port is chosen over a two wire one. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is SN65HVD70DR full duplex? Yes. It has separate driver outputs and receiver inputs on a 14 pin SOIC, so the link sends and receives at the same time on four wires.

How many nodes can the bus carry? Up to 256 at 1/8 unit load, with termination only at the two ends of the bus.

What is the floor life? Moisture level 2 with a one year floor life, so a reel open for more than a year needs a bake before reflow.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.