Contact Us

SN65HVD3085EDR

Brand: Texas Instruments
Texas Instruments SN65HVD3085EDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD3085EDR — Power Management & Signal Chain | Superb Automation

SN65HVD3085EDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD3085EDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD3085EDR: 1 Mbps RS-485 transceiver that draws 0.3 mA while listening

SN65HVD3085EDR is a half duplex differential driver and receiver built to the 75176 footprint, with a shutdown mode in the nanoamp range and a receiver that holds a defined output with the bus open, shorted or idle in a SOIC body of 8 pins. It is the 1 Mbps member of a family that spans 200 kbps to 20 Mbps, runs at 0.3 mA typical active current and a few nanoamps in shutdown, loads the bus at 1/8 unit so 256 nodes fit on one pair, carries 15 kV of bus pin ESD protection, keeps the industry standard SN75176 footprint, and is specified from minus 40 to plus 85 degrees air temperature, with the D body of the 200 kbps member characterised to 105 degrees. Power on reset holds the outputs high impedance until the rail is stable, and a thermal shutdown protects the driver against a fault.

Order code and package

SN65HVD3085EDRSOIC D body, 8 pins, printed Obsolete in the addendum dated 10 August 2026 with no quantity and no carrier. The active row for this rate is the DGKR body, so this exact string is not the one to order for a new build
SN65HVD3085EDGKRVSSOP DGK body, 8 pins, Active, 2500 pieces on a large reel, moisture level 1 with unlimited floor life, minus 40 to plus 85 degrees, marking NWK
SN65HVD3082E200 kbps, and the D body of this member is characterised to 105 degrees air temperature rather than the 85 of the rest of the family
SN65HVD3088E20 Mbps, for a short terminated link. The three members share the pinout and the footprint, so the rate is the only electrical difference in the interface
SN75HVD3082Ethe commercial temperature version, 0 to 70 degrees, for a consumer or office product that does not need the industrial range

Electrical parameters that decide the application

Supplya 3.3 V rail with 5 V tolerant logic, so the port works behind either controller family on the same footprint
Signalling rate1 Mbps on this member, against 200 kbps and 20 Mbps on its siblings, each printed in the same document
Quiescent current0.3 mA typical in the active mode excluding the load, which is one of the lowest figures in the 3.3 V RS-485 class and the reason the family is used on metering nodes
Shutdown currenta few nanoamps, which is the number a battery fed node has to meet when it is not listening
Node count1/8 unit load, up to 256 nodes on one bus, with termination only at the two ends
ESDup to 15 kV on the bus pins, the family figure, measured at the pins
Footprintthe industry standard SN75176 outline, so a board built for the older 5 V part can take this 3.3 V one without a copper change
Fail safea defined receiver output with the bus open, shorted or idle, so a controller does not read a false start bit when a connector is pulled
Power on resetthe outputs stay high impedance until the supply is stable, which is what stops a hot plugged node from driving the pair during power up
Thermal shutdownon the driver, for a sustained bus fault at high ambient
Shutdown modean inactive shutdown state with the supply current in the nanoamp range, so a polled node can be parked between frames
Temperatureminus 40 to plus 85 degrees for this member, with the 200 kbps D body characterised to 105 degrees, and the commercial 75 prefix at 0 to 70

Family variants and how they differ

3085E against 3082E1 Mbps against 200 kbps, and the slower member has a 105 degree D body variant. A long, slow metering bus takes the 3082E
3085E against 3088E20 Mbps against 1 Mbps, for a short backplane. The higher rate needs termination and a short stub, and the quiescent current is higher
Against a 5 V 75176same footprint, one third of the supply current and a 3.3 V rail. The only thing lost is the wider common mode headroom of the 5 V part
Against an isolated partan ISO3082 class device isolates the port and needs an isolated supply. A bus inside one cabinet does not need the barrier
Against a fault protected transceiverthe 1794 family survives 70 V on the bus pins and this one does not. A bus that can be miswired to a supply needs the fault rating

Points to check before this part goes on a BOM

The string on this page is obsolete and the live part at the same rate is the DGKR body. That is the single most useful sentence on the page for a buyer, because a bill of materials that carries the SOIC string will be quoted by a broker at a broker price, and the honest alternative is the VSSOP body at 2500 pieces on a large reel with the NWK marking. A board that cannot take the smaller body needs a stock check on the existing SOIC strings rather than an assumption that they are still made.

The 0.3 mA figure is the active listening current and it is what makes a solar or loop powered node possible. The driver current in the dominant state follows the bus load, so a node that transmits rarely can stay in the microamp class for most of its life. A budget built on the quiescent figure alone will be wrong by the duty cycle of the transmissions.

The nanoamp shutdown current is only reached with the enable pins in the shutdown state, and the part then cannot receive. A node that has to wake on the first byte of a frame cannot use the shutdown mode at all and has to stay in the 0.3 mA listening state, which changes the energy budget by three orders of magnitude.

The 15 kV bus pin rating is a human body model figure and it is the family number, not a board level claim. A connector on a panel that is touched by a charged cable adds a path that the pin rating does not describe, and a product that has to pass a system level ESD test needs the external protection as well.

The temperature range of this member stops at 85 degrees while the 200 kbps member has a D body characterised to 105. That is not an accident of the data sheet, it is the test coverage for that specific body, and a customer who needs the faster rate at 100 degrees ambient has to accept the lower junction margin or move to a different family.

The 256 node count is a receiver loading figure and assumes the bus is terminated once at each end. Adding a terminator at every node is a common field error and it loads the driver until the differential output falls below the standard minimum, which shows up as a link that works with two nodes and fails with ten.

Why the 75176 footprint still matters

An installed base of 5 V industrial boards uses the 75176 pinout, and a change to 3.3 V that keeps that footprint needs no copper change, no new qualification of the connector and no new test fixture. The family was built around that constraint and it is why the part is still specified on boards that have nothing legacy about them.

The cost of the smaller VSSOP body is a new footprint, a new stencil aperture and a first article inspection. On a new board that is free, and on a board that is being re sourced it is the reason a customer may prefer a broker stock of the SOIC string over the active VSSOP one.

What the order code decides

The string reads SN65HVD3085E for the device at 1 Mbps, D for the SOIC body and R for the reel, with DGKR for the VSSOP body. The 3082 and 3088 numbers are different rates, not suffixes, and the 75 prefix is the commercial temperature grade. The body letter is the difference between an obsolete row and an active one on this exact part, so it cannot be treated as a packing detail.

Where this order code fits

Energy meter networks, motor control, power inverters, industrial and building automation, battery powered applications and telecom equipment are the applications the vendor prints, and a loop powered or solar fed node that listens most of the time is the case this member is bought for. Teams comparing it with a neighbouring part start from our Component Obsolescence Management page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is SN65HVD3085EDR still orderable? The SOIC string is printed Obsolete in the current addendum. The active row at the same rate is SN65HVD3085EDGKR, 2500 pieces on a large reel, minus 40 to plus 85 degrees.

What is the shutdown current? A few nanoamps. The active listening current is 0.3 mA typical, which is the figure a node that must stay listening has to use.

How many nodes can one bus carry? Up to 256 at 1/8 unit load, with termination only at the two ends of the pair.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.