Contact Us

SN65HVD251DR

Brand: Texas Instruments
Texas Instruments SN65HVD251DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD251DR — Power Management & Signal Chain | Superb Automation

SN65HVD251DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD251DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD251DR: an industrial CAN transceiver that survives 36 V on the bus

The SN65HVD251DR is a 5 V CAN transceiver built for the industrial side of the CAN world rather than the vehicle side. It carries differential transmit and receive between a CAN controller and the bus at rates up to 1 Mbps, it meets ISO 11898, and it holds the bus pins safe against minus 36 V and plus 36 V faults, which is what happens when a 24 V supply is wired to a data pair by mistake.

It is published as a drop in improved replacement for the PCA82C250 and PCA82C251, which is the pair of parts a lot of older industrial boards still carry. The common mode range is minus 7 V to plus 12 V, the transients it tolerates reach plus or minus 200 V, and it allows up to 120 nodes on one bus. A standby mode drops the current to about 200 uA typical, and an unpowered node does not disturb the bus, which matters when a card is pulled from a live rack.

Key data for the SN65HVD251DR

StandardISO 11898 CAN physical layer, signalling rates up to 1 Mbps
Fault toleranceBus fault protection minus 36 V to plus 36 V, transient tolerance plus or minus 200 V, loss of ground protection
NodesHigh input impedance, up to 120 nodes on a bus
ESDBus pin protection above 14 kV human body model, charged device model published in the same table
PowerLow current standby mode at around 200 uA typical, thermal shutdown, glitch free power up and down for hot plugging
ReceiverCommon mode range minus 7 V to plus 12 V, differential input hysteresis of several hundred millivolts

Body, marking and reel data

BodyD, SOIC 8 at 4.90 mm by 3.91 mm, pin compatible with the PCA82C250 and PCA82C251
Reel2500 pieces on a large reel for the plain, .A and G4 rows, carrier tape 12.4 mm
MarkingHVD251 on the G4 row, a different code on the .A row, so the row has to be named on the order
HandlingMoisture level 1, 260 C peak, unlimited floor life on the rows that publish a level
TemperatureMinus 40 C to 125 C, the industrial and automotive adjacent range rather than the 85 C ceiling

Why the 36 V bus rating is the selling point

A CAN bus runs on two wires that are often in the same cable bundle as a 24 V supply and a motor drive. A miswire that puts 24 V on CANH is a commissioning accident, not a board fault, and a transceiver without bus fault protection dies with the mistake. The SN65HVD251DR clamps and survives, the node reports nothing, and the technician fixes the wiring rather than the board.

The unpowered node behaviour covers the same ground from a different direction. When a card is removed from a live rack, or when its 5 V rail collapses before the bus goes quiet, the transceiver must not load the bus and must not drive it. The part goes high impedance in that state, so the remaining nodes keep talking while the card is swapped, which is what a hot pluggable rack requires.

Questions we get when this code is on a BOM

The first question is whether this part can replace a PCA82C250 directly. Electrically it is published as an improved replacement and the pinout matches, but the PCA82C250 has a slope control pin that some boards tie to ground for the fastest edge. On the SN65HVD251DR the same pin selects one of three modes, so a board that assumed slope control has to be checked before the swap, and the check is a look at the circuit, not a datasheet comparison.

The second question is about the two supply rails. The 251 is a 5 V part; the 3.3 V equivalent in our catalogue is a different family and has different bus fault ratings. A build that mixes them across a network still works, because CAN is defined by the bus levels and not by the transceiver supply, but the fault tolerance of each node is not the same and the network is only as robust as the weakest node. Where a mixed network is unavoidable, the 5 V node usually sits next to the drive and the 3.3 V node on the logic side, which keeps the fault exposure where the protection is strongest.

How SUPERB supports this line item

We carry the SN65HVD251DR for industrial control and drive builds and we state the marking and the reel row on every offer, because the three active rows of this string print different codes. Customers converting a PCA82C250 or PCA82C251 board can start from our CAN bus transceiver selection page, which sets out the mode pin differences between the two parts.

Where a customer is keeping a legacy board alive and the original part is no longer available, the obsolete part cross reference hub collects the pinout, the mode pin and the fault rating checks we run before proposing a substitute.