SN65HVD232QDR
Product Specifications
SN65HVD232QDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN65HVD232QDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN65HVD232QDR: a 3.3 V CAN transceiver for a 1 Mbps bus
The SN65HVD232QDR is the basic member of the SN65HVD23x family of 3.3 V CAN transceivers. It provides differential transmit and receive capability between a CAN controller and the bus at rates up to 1 Mbps, it meets ISO 11898-2, and it fits the PCA82C250 footprint that a generation of 5 V boards used, which is what makes it a common replacement part on control boards that moved their logic to 3.3 V.
Unlike its two siblings it has no standby or sleep mode pin: the 230 offers a 370 uA standby and the 231 a 40 nA sleep, while the 232 is always on. For a node that is powered continuously and has no interest in a low power state that is the right trade, because it removes a control line and the software that drives it. The bus pins survive more than 16 kV of human body discharge and the part allows up to 120 nodes on one bus.
Key data for the SN65HVD232QDR
| Standard | ISO 11898-2 high speed CAN physical layer, data rates up to 1 Mbps |
| Supply | Single 3.3 V rail, compatible with 3.3 V controllers and with 5 V tolerant logic on the host side |
| Nodes | High input impedance allows up to 120 nodes on one bus segment |
| Protection | Bus pin ESD above 16 kV HBM, thermal shutdown, open circuit failsafe, glitch free power up and down |
| Compatibility | Low power replacement for the PCA82C250 footprint, used in CANopen, DeviceNet and CAN Kingdom networks |
| Family modes | 230 standby at 370 uA typical, 231 sleep at 40 nA typical, 232 always on with no mode pin |
Body, marking and reel data
| Body | D, SOIC 8 at 4.90 mm by 3.91 mm, the footprint shared with the PCA82C250 |
| Reel | 2500 pieces on a large reel on the G4 row, carrier tape 12.4 mm, 330 mm reel |
| Marking | VP232 printed on the SOIC rows of the family file |
| Addendum status | The plain row prints no status and no quantity with Call TI in the finish column, the .A row prints Obsolete, the G4 row prints Active at 2500 pieces |
| Temperature | Minus 40 C to 85 C on the published rows |
What the always on member suits
A CAN node that stays awake is common in industrial controllers, motor drives and building equipment: the bus is polled constantly and there is no reason to pay for a wake circuit. Removing the standby pin removes one GPIO, one pull resistor and one line of start up code, and on a board that already has forty parts that matters. The cost is quiescent current, which is a few tens of milliamps with the driver active and is well inside the budget of a mains powered unit. The thermal path is the other reason the part suits enclosed control boxes: the SOIC 8 body dissipates a fraction of a watt at 1 Mbps, and the vendor publishes the junction to ambient figure so a cabinet temperature rise can be checked before the board is signed off.
The 120 node limit is set by the input impedance of the transceiver, and it is generous for a segment that ISO 11898 expects to carry 30 to 64 nodes over 40 m. Where a network grows past that, the answer is a repeater or a second segment, not a different transceiver.
Questions we get when this code is on a BOM
The important question is about the Q in the order string. The vendor addendum in the current revision prints SN65HVD232DR, its .A row and its G4 row, and does not print a Q string at all. That means the automotive or extended qualification of this code, if it exists, is released under another document, and a buyer who needs an AEC-Q100 part should not assume that a Q in the catalogue entry proves it. We confirm the qualification route before quoting.
The second question is about the family mix. Because the 230, 231 and 232 share a body and a pinout, a substitution between them is physically possible and functionally wrong if the board drives the standby pin. We check whether pin 8 is connected before proposing any swap, and we say which mode pin the replacement expects.
How SUPERB supports this line item
We quote the SN65HVD232QDR with the qualification question stated rather than implied, and we supply the 230 and 231 members when a build needs a low power mode. Customers picking a CAN transceiver for a new node can use the CAN bus transceiver selection page, which compares the mode pins, the node counts and the rail voltages across the families we carry.
For boards that are moving from a 5 V CAN transceiver to 3.3 V, the how to verify a drop in replacement checklist covers the level compatibility of the RXD and TXD pins, which is where most of these swaps go wrong.