Contact Us

SN65HVD22DR

Brand: Texas Instruments
Texas Instruments SN65HVD22DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD22DR — Power Management & Signal Chain | Superb Automation

SN65HVD22DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD22DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD22DR: 500 kbit/s RS-485 for cable runs up to 1200 m

The SN65HVD22DR is the slow, long distance member of the SN65HVD2x family. Its driver output is slew limited so that a 500 kbit/s signal keeps its shape over 1200 m of twisted pair, and it connects up to 256 nodes on the same segment. The extended common mode window of minus 20 V to plus 25 V is shared with the rest of the family, as is the failsafe receiver that reports a high level within 250 microseconds of losing the signal.

This is the part for building automation, energy metering and any installation where the cable is already in the wall and cannot be shortened. Trading rate for distance is the whole point: 500 kbit/s is enough for a polling loop over hundreds of meters, and the shaped edges keep the emissions low enough that the cable does not need to be shielded in most cabinets.

Key data for the SN65HVD22DR

Rate and reachUp to 500 kbit/s over up to 1200 m of Belden 3105A class cable, 256 nodes on the segment
Common modeMinus 20 V to plus 25 V, more than double the standard RS-485 window
DriverSlew limited output for low radiated noise and for signal quality on long stubs, current limited in both directions
ProtectionBus pins above 16 kV HBM, thermal shutdown, glitch free power up and power down for live insertion
Current5 mA typical and 8 mA maximum with the driver enabled, 1 uA maximum in standby
ReceiverMore than 100 mV hysteresis, failsafe high on open, shorted or idle bus within 250 microseconds

Body, marking and reel data

BodyD, SOIC 8 at 4.90 mm by 3.91 mm, the same footprint as the faster members of the family
Reel2500 pieces on a large reel per the tape and reel table, carrier tape 12.4 mm
MarkingVP22 on the SOIC body and 65HVD22 on the DIP body of the same family
Addendum slipThe plain SN65HVD22DR row prints 50 pieces in a tube with moisture marked N/A for package type, on a string whose R suffix means a reel, so the row reads as a column shift
TemperatureMinus 40 C to 85 C on every published row

Matching the rate to the cable

RS-485 data rate and cable length trade against each other through the rise time of the driver and the loss of the pair. A 500 kbit/s edge takes about 2 microseconds per bit, and a twisted pair carries that shape further than a 20 Mbps edge before the eye closes. The family table quantifies it: 1200 m at 500 kbit/s, 150 m at 5 Mbps, 50 m at 25 Mbps. Choosing the member from that table rather than from the fastest available part is what keeps a retrofit working on the existing wiring.

Stub length is the other limit. Every node taps the bus with a short stub, and each stub adds a reflection. At 500 kbit/s a stub of a few tens of centimetres is tolerable, and the slew limited driver tolerates more than a fast one. Installations that add nodes over time eventually exceed the stub budget, and the symptom is a bus that works until the last cabinet is connected. The arithmetic is simple: sum the stub lengths, compare against a tenth of the electrical wavelength at the chosen rate, and keep margin for the connectors.

Questions we get when this code is on a BOM

The first question is whether a 5 Mbps part can simply replace this one to gain speed. It can be fitted, because the pinout and the body match, but the cable in the wall decides whether the link still works. We ask for the cable type and the run length before agreeing to a substitution, and we say plainly when the answer is that the cable, not the transceiver, is the limit.

The second question is about the reel quantity, and here the vendor file is unclear. The plain row prints 50 pieces in a tube while the tape and reel table prints 2500 on a 330 mm reel for the same string. We quote the row and the quantity we can confirm from the vendor, and we do not repeat the tube figure as if it applied to an R suffix part.

How SUPERB supports this line item

We supply the SN65HVD22DR for building automation and metering builds, with the reel quantity confirmed against the vendor tape table rather than the addendum row alone. Customers replacing an older 75176 class transceiver can start from our pin to pin cross reference page, which lists the SN75176 footprint checks we run.

Where a site is being extended and the extra nodes push the stub budget, the component shortage forecast page explains how we plan the second batch of transceivers and terminators against the installation schedule.