Contact Us

SN65HVD179DR

Brand: Texas Instruments
Texas Instruments SN65HVD179DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD179DR — Power Management & Signal Chain | Superb Automation

SN65HVD179DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD179DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD179DR: 5 V full duplex RS-485 transceiver with balanced thresholds and no enables

SN65HVD179DR is a differential driver and receiver pair on a single 5 V rail with separate bus pins for each direction, built for fieldbus networks that need a defined receiver state with the bus idle in a SOIC body of 8 pins. It runs to 25 Mbps, loads the bus at half a unit load so 64 nodes fit on one pair, and needs no enable pins at all, so the driver is always on. The feature list prints 15 kV human body model on the bus pins and the ESD table prints 16 kV on the bus pins with ground, 4 kV on all pins and 1 kV charged device model. A bus fault of minus 7 V to plus 12 V is tolerated, driver propagation is 4 ns typical and 12 ns maximum, receiver propagation 24 ns typical and 40 ns maximum, and the junction to ambient figure is 230.8 degrees per watt in the eight pin body.

Order code and package

SN65HVD179DRSOIC D body, 8 pins, Active, 2500 pieces on a large reel, minus 40 to plus 85 degrees, marking VP179. The plain row prints the finish as Call TI
SN65HVD179DR.Athe same reel with NIPDAU finish and moisture level 1 with unlimited floor life, which is the row a material declaration should name
SN65HVD179DRG4the lead free declaration of the same reel, NIPDAU, level 1, and a second row with the same string carries the same data
SN65HVD179Dthe tube row of the same body, printed Obsolete with no quantity and no carrier
document scopethe datasheet covers one device and one package, so there is no sibling row to compare against. The family around it, with fault protection and cable invert, is documented separately

Electrical parameters that decide the application

Supply4.5 V to 5.5 V on a single rail. A 3.3 V system needs a different part, and the 5 V rail here also sets the receiver output swing that drives the controller
Signalling rate25 Mbps, which is well above any fieldbus rate this part is used at. The rate is not the reason to buy it, the threshold behaviour is
Duplexseparate A and B receiver inputs and Y and Z driver outputs, so the part works on four wires and each direction has its own pair
Node counthalf a unit load, so 64 nodes on one bus. The loading is the input impedance of the receiver, and terminators add to the DC load on top of it
Enablesthere are none. The driver and the receiver are permanently active, which removes the direction control pin and the firmware that goes with it, and removes the option of releasing the pair
Balanced thresholdsthe receiver switches with an internal offset so an idle, open or shorted bus reads a defined level without external fail safe resistors. The front page draws the window between minus 0.10 V and minus 0.20 V, and the receiver table prints 50 mV of hysteresis
Bus faultminus 7 V to plus 12 V on the bus pins, which is the range a miswired or ground shifted field bus puts on the pair before the part is damaged
ESD16 kV human body model on the bus pins with ground, 4 kV on all pins and 1 kV charged device model in the ESD table, while the feature list rounds the bus figure to 15 kV. Both are pin ratings and neither replaces board level protection
Driver switching4 ns typical, 8 ns maximum for the rise and 12 ns maximum for the total propagation, with a pulse skew small enough that a 25 Mbps eye stays open on a short pair
Receiver switching24 ns typical and 40 ns maximum, which is slower than the driver and sets the round trip delay of a repeater built from two of these
Thermal230.8 degrees per watt junction to ambient on a low K board, which is a high number for an eight pin body and the reason a continuously transmitting node runs warm
Temperatureminus 40 to plus 85 degrees, narrower than the 125 degree isolated parts in the same cabinet

Family variants and how they differ

Against SN65LBC179Athat part is a 30 Mbps pair on 5 V with no enables either, but it has no balanced threshold offset. The 179 is chosen when the bus has to read a defined level with no driver, the LBC179A when the link is point to point and the receiver only ever sees a driven pair
Against a fault protected transceiverthe family with 70 V bus fault protection and cable invert survives a miswire to a supply rail. This part tolerates minus 7 V to plus 12 V, which covers a ground shift and not a 24 V mistake
Against the 3.3 V familyan SN65HVD1473 runs on 3.3 V at 20 Mbps with 256 nodes and enable pins. Moving to it means a new rail decision and a new direction control path in the firmware
Against an isolated partan ISO1450 removes the ground difference problem and needs an isolated supply on the bus side. A pair that stays inside one enclosure does not need the barrier
Against a 75176 style transceiverthe older part needs an external fail safe network to hold the receiver output with the bus idle, and it loads the bus at a full unit load, so a long multidrop trunk gets fewer nodes

Points to check before this part goes on a BOM

The part has no enable pins, and that is a topology decision rather than a missing feature. It suits a node that owns its transmit pair, which is the four wire fieldbus case, and it suits a listen only tap. It does not suit a two wire multidrop bus where several nodes take turns, because a driver with no enable cannot be parked and two active drivers on one pair destroy the frame.

The balanced receiver threshold is the feature that makes this part worth its price in a fieldbus. With the bus idle, an ordinary receiver can sit in its linear region and output noise, which the controller reads as a stream of start bits. The internal offset moves the switching point so an idle pair reads a stable level, and that removes the external fail safe bias resistors that older networks needed.

The datasheet prints two protection figures that do not match: the feature list says 15 kV human body model and the ESD table says 16 kV on the bus pins. Both are pin ratings under the human body model, and neither is a claim about a connector or a cable. A customer who needs a board level number has to test the board, because the transceiver rating is only one element of it.

The finish column on the plain DR row is printed as Call TI, while the .A and G4 rows of the same reel print NIPDAU with moisture level 1. As with the rest of this catalogue, the string that carries the paperwork is the one with the suffix, and a purchaser who orders by the short string may receive a reel whose label does not state a finish at all.

The junction to ambient figure of 230.8 degrees per watt is measured on a low K board with no airflow. An eight pin SOIC dissipating a few hundred milliwatts in still air climbs tens of degrees, and a node that transmits continuously in a sealed enclosure will run near the top of its 85 degree window. Spreading copper under the part is a cheaper fix than a heatsink and is worth writing into the assembly notes.

The 25 Mbps ceiling is far above the fieldbus rates this part is used at, and that headroom is deliberate. Buying speed here is not the point; buying the threshold behaviour and the four wire topology is. A customer comparing this part with a faster transceiver on price per megabit is comparing the wrong numbers.

Where a full duplex pair belongs

Motor control, utility metering, chassis to chassis links and point of sale networks are the applications the vendor prints, and all of them have a controller at one end that owns the link. INTERBUS is named as well, which is a ring that runs at a fixed fieldbus rate well under the ceiling of this part.

In those systems the receiver is always listening and the driver is always driving, so a part without enables removes two control lines, two firmware states and the timing question of when it is safe to turn the driver around.

What the order code decides

The string reads SN65HVD179 for the device, D for the SOIC body and R for the large reel of 2500. The tube row is printed Obsolete, so the reel is the only orderable form. The G4 suffix is the lead free declaration.

Nothing in the string selects the threshold behaviour, the node count or the ESD level, because the document covers a single device. A substitution therefore means a different part number and a re-check of the bus, not a different reel letter.

Where this order code fits

Fieldbus nodes in motor control, metering, building automation and point of sale equipment where the network needs a defined receiver state with the bus idle and the two directions have their own pair. Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it have driver enable pins? No. The driver and receiver are permanently active, which is why the part suits a four wire link or a listen only tap and not a two wire multidrop bus.

How many nodes fit on one bus? 64, because the receiver presents half a unit load. Terminators and cable capacitance reduce the practical number.

What happens when the bus is idle? The balanced threshold makes the receiver read a defined level without external fail safe resistors, which is the reason this part is chosen for fieldbus work.

Which string should a material declaration name? SN65HVD179DR.A or SN65HVD179DRG4. Both print NIPDAU finish and moisture level 1, while the plain DR row prints Call TI in both columns.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.