Contact Us

SN65HVD1477DGKR

Brand: Texas Instruments
Texas Instruments SN65HVD1477DGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD1477DGKR — Power Management & Signal Chain | Superb Automation

SN65HVD1477DGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD1477DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD1477DGKR: 3.3 V full duplex RS-485 transceiver at 50 Mbps with 30 kV of bus protection

SN65HVD1477DGKR is a differential driver and receiver with separate pins for each direction, fully enabled, built for 50 Mbps and for the widest temperature and transient range in the family in a VSSOP body of 8 pins. It runs from 3 V to 3.6 V, carries 50 Mbps, presents one eighth of a unit load so 256 nodes fit on one bus, and survives 30 kV human body model and 16 kV of IEC contact discharge on the bus pins. The receiver keeps 70 mV of hysteresis, the quiescent current stays under 1.1 mA, standby falls to 10 nA typical, the logic inputs tolerate 5 V, and the part is characterised from minus 40 to plus 125 degrees with a 150 degree junction limit.

Order code and package

SN65HVD1477DGKRVSSOP DGK body, 8 pins, 2500 pieces on a large reel, Active in the addendum dated 10 August 2026, NIPDAU finish, moisture level 1 with no floor life limit, marking 1477, minus 40 to plus 125 degrees
SN65HVD1477DRthe SOIC D body, 8 pins, 2500 on a large reel, marking VD1477. Two bodies, two footprints and the same silicon, so the choice is a board question
The DGKR row printed at 75 on a SOIC 14the same addendum also prints a DGKR row against a SOIC 14 body at 75 pieces in a tube, which is a column shift in that table. The real VSSOP rows are the 2500 piece reel and the 75 piece tube, and the reel count should be confirmed before an order is placed against the tube
SN65HVD1471 and SN65HVD1474the 400 kbps and 20 Mbps members, fully enabled like this one, with the 1470 and 1473 and 1476 carrying enables instead, so the six strings are two enable strategies across three rates
The 1470 groupthe members with an active high driver enable and an active low receiver enable, with a standby current below 5 uA, which is the row to quote when a node has to be silenced

Electrical parameters that decide the application

Signalling rate50 Mbps on this member, against 20 Mbps on the 1474 and 400 kbps on the 1471, all in the same document and the same bodies
Unit loadone eighth of a unit load, 256 nodes on one bus, which is the load the fractional input presents and the number that decides the node count
Duplexfull duplex, so the driver pair and the receiver pair are separate and both directions run at once, which means four wires
Driver differential output1.5 V minimum into a 54 ohm load measured across the recommended range, with the load resistance printed as 54 to 60 ohm and the load capacitance as 50 pF
Hysteresis70 mV on the receiver, which is the margin against common mode noise on a long run and the figure the family was built around
ESDmore than 30 kV human body model on the bus pins and ground, and 40 kV per the all pin JEDEC row, which is the highest figure in the RS-485 families here
Transientmore than 16 kV of IEC 61000-4-2 contact discharge and more than 4 kV of IEC 61000-4-4 fast transient burst on the bus pins and ground
Quiescent currentbelow 1.1 mA during operation, which is what the 3.3 V supply and the low power receiver allow
Standby current10 nA typical and below 5 uA maximum on the members that carry enables, so a node can sit for years on a small cell
Enable pinsthis member has none, which means the driver is always on and the board has to be a point to point or a star link rather than a shared bus
Thermaloperation specified to a 150 degree junction with an internal shutdown, so the ambient rating of 125 degrees is not the whole thermal budget and self heating has to be added to it
Temperatureminus 40 to plus 125 degrees on every active row of this string, the widest in the family

Family variants and how they differ

1477 against 1476the 1476 is the same 50 Mbps with enables and a standby current below 5 uA. A node that has to be silent on a shared bus uses the 1476, and a point to point link uses the 1477 with two fewer pins to drive
1477 against 147420 Mbps against 50 Mbps in the same body. The slower member tolerates a longer cable, so a 100 m link at 50 Mbps is a mistake the 1474 does not make
Against the HVD34 family5 Mbps and 250 piece reels at 85 degrees. This family is faster, hotter and better protected, and it costs more, so the older part remains right for a slow long line
Against an isolated transceiveran ISO3080 class part puts a barrier in the package for a link across a ground boundary. This family has no barrier, so a link between buildings is the case for the isolated part
Against a 5 V parta 5 V full duplex transceiver with the same rate exists and needs a level shifter for a 3.3 V controller. This family removes the shifter and keeps the bus levels

Points to check before this part goes on a BOM

A part with no enable pins is always driving. On a point to point link that is exactly right and it saves two control lines. On a shared bus it is a bus contention waiting to happen, and no amount of care in the controller fixes it because the driver is on whenever the supply is. This single property decides whether the 1477 or the 1476 goes on the board, and it is worth stating in the offer.

The 150 degree junction limit is the number behind the 125 degree ambient rating. At 50 Mbps with a 54 ohm load the output stage dissipates a few tens of milliwatts, and the junction rises above the ambient by the thermal resistance of the eight pin body. A cabinet at 110 degrees ambient leaves very little junction margin, so the thermal table and not the ambient figure is where a high temperature quote has to be checked.

The 30 kV human body model rating is a handling and service figure. It says the pins survive the discharge of a technician and the strike of a cable, and it does not say the part survives a lightning induced surge on a long cable. A link that runs between buildings needs an external surge device whatever the transceiver rating says, and quoting the 30 kV figure as if it covered that is a claim the customer's test house will reject.

Full duplex at 50 Mbps needs four wires that are all treated as transmission lines. At a 20 ns bit time the round trip on a 10 m cable is a significant fraction of a bit, so termination at both ends and a controlled impedance cable are not optional. A customer who built a 5 Mbps link on a two pair cable and expects the same cable to carry 50 Mbps is asking the cable to do something it cannot.

Standby current of 10 nA belongs to the members with enables, not to this string. A board that needs the 10 nA figure has to use the 1476 and drive the enable pins, and a board that uses this part has no way to reach that state. That is a small distinction with a large consequence in a battery powered board and it belongs in the first paragraph of a quote for either part.

The packaging table has a column shift on one row, printing a DGKR row against a SOIC 14 body in a 75 piece tube. The real VSSOP rows are the 2500 piece reel and the 75 piece tube. This is the kind of print defect that produces a wrong quantity on a purchase order, and the reel count should be confirmed against the label rather than against the table.

Where 50 Mbps earns its price

A motion control loop that closes at 10 kHz across eight axes produces a lot of small frames, and at 20 Mbps the bus is the bottleneck. At 50 Mbps the same traffic fits with margin, which is why the fast members of this family appear in machine tools and in test equipment rather than in building automation.

The price of that speed is a short cable and a careful termination. The families that run 1500 m run at 115 kbps, and the two requirements cannot be met by one part. A customer who asks for both is asking for a repeater, and that is a different conversation.

Reading the order code

SN65HVD1477 reads as the family, HVD for the transceiver and 1477 for the fully enabled 50 Mbps member. The DGK at the end is the VSSOP body and the R is a reel. The rate and the enable strategy are in the number, so a substitution between the 1471, 1474 and 1477 changes the speed, and a substitution between the 1476 and the 1477 changes whether the driver can be turned off.

Where this order code fits

Industrial automation, encoders and decoders and any four wire link that has to carry both directions at 50 Mbps are the stated applications, and the common thread is a channel short enough to support the rate. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can the driver be turned off? No. This member has no enable pins, so the driver is on whenever the supply is. A shared bus needs the 1476 which carries enables.

How many nodes fit on the bus? 256, from the one eighth unit load, provided the cable and the termination support the rate at that node count.

Does the 30 kV rating cover a surge on a long cable? No. It is a handling and service rating. A cable that leaves the building needs an external surge device regardless of the transceiver figure.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.