Contact Us

SN65HVD1050DR

Brand: Texas Instruments
Texas Instruments SN65HVD1050DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD1050DR — Power Management & Signal Chain | Superb Automation

SN65HVD1050DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD1050DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD1050DR: EMC optimised CAN bus transceiver, 1 Mbps, SOIC-8

SN65HVD1050DR is a CAN transceiver that connects a controller to a differential bus with fault protection to 27 V and low emissions in a SOIC (D) body of 8 pins. It drives and receives a CAN bus at up to 1 Mbps, survives a bus fault from -27 V to 40 V, and is specified as an improved replacement for the TJA1050 with lower emissions.

Order code and package

Ordering stringSN65HVD1050DR, D package, 8-pin SOIC, tape and reel
Family roleEMC optimised CAN transceiver, an improved replacement for the TJA1050
Package8-pin SOIC, 4.90 mm by 3.91 mm
Ambient range-40 C to 125 C
Bus standardISO 11898-2, plus SAE J2284, SAE J1939, ISO 11783 and NMEA 2000 interfaces
Pin count checkD, R, S, VCC, GND, CANH and CANL, with the eighth pin for the split or reference function

Electrical parameters that decide the application

Data rateUp to 1 Mbps
Bus fault protection-27 V to 40 V on the bus pins
Common mode range-12 V to 12 V
Transient withstand-200 V to 200 V per ISO 7637
ProtectionsCross wire, over voltage, loss of ground, thermal shutdown, dominant time out
EmissionsLow EME by specification, with high immunity to conducted disturbance
Power up behaviourGlitch free bus inputs and outputs during power cycling

Points to check before this part goes on a BOM

Dominant time out is the protection that a controller cannot provide for itself. If a software fault holds the transmit data low, the transceiver would drive a permanent dominant level and every other node on the bus would lose communication. The internal timer releases the driver after a defined period, so one faulty node cannot take down the network, and the recovery is automatic once the data line returns high.

The minus 27 V to 40 V fault range covers the wiring errors that happen in a vehicle or a machine. A short from the bus to battery, a reversed connection or a lost ground all put a steady voltage on a pin that is normally a differential pair, and the transceiver has to survive it without latching. A part rated to the 12 V bus alone fails this test on the first miswired harness.

Low emissions matter because CAN runs in the same harness as the radio and the sensors. The edge rate of the driver is shaped to keep the spectrum below the limits in the automotive EMC standards, and the same shaping costs a little bit of timing margin at 1 Mbps. A faster transceiver in the same socket can improve the eye diagram and fail the EMC test, which is why the EMC specification belongs in the selection criteria and not in the appendix.

The -12 V to 12 V common mode range is what allows nodes at different ground potentials to talk. In a long machine the ground difference between two cabinets can be several volts, and a transceiver with a narrower range will read that offset as a bus fault. The 24 V span is the protocol requirement, and parts that quote less are only usable on short, single-cabinet buses.

The replacement claim is specific and worth checking against the board. The part is pin compatible with the TJA1050 and specified to meet or exceed its behaviour, which matters when a product is being re-sourced because the original is hard to find. The five volt supply, the pinout and the timing have to match, and the differences are in the EMC and the fault protection rather than in the digital interface.

Thermal shutdown protects the driver when the bus is shorted to a supply and the output stage is asked to drive current continuously. The junction temperature rises until the internal sensor turns the driver off, and the receiver stays alive so the node can still hear the bus. A controller that reports a bus off condition and recovers on its own is behaving correctly, and a transceiver without the shutdown feature fails permanently in the same event.

Stub length is a physical limit that no transceiver can fix. At 1 Mbps the bit time is 1 microsecond and the signal has to settle within a fraction of it, so a node tapped off the main pair with a long stub produces a reflection that shows up as a bit error only at the far end of the bus. Keeping the stub under about 0.3 m and terminating only at the two ends is the standard arrangement, and the transceiver's fault protection does nothing for a reflection because the bus is electrically healthy.

Where this order code fits

It is used in industrial automation and DeviceNet buses, automotive high speed CAN, SAE J1939 and ISO 11783 machine networks and NMEA 2000 marine buses, wherever a controller has to be connected to a differential bus that runs through a harsh harness. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Defense Grade Components page.

Questions buyers ask

Is it a drop-in replacement for the TJA1050? The pinout and the 5 V supply match, and the part is specified as an improved replacement, so the check is the bus timing and the EMC behaviour on the actual board rather than the pin map.

Does it support 1 Mbps? Yes, up to 1 Mbps, which is the maximum for classical CAN. CAN FD needs a different transceiver with a higher loop delay specification.

What happens if the bus is shorted to battery? The bus pins survive -27 V to 40 V, and the driver reports the fault condition while the thermal shutdown protects the output stage if the short persists.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.