Contact Us

SN65HVD101RGBT

Brand: Texas Instruments
Texas Instruments SN65HVD101RGBT is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD101RGBT — Power Management & Signal Chain | Superb Automation

SN65HVD101RGBT

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD101RGBT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD101RGBT: an IO-Link PHY with its own regulator inside the package

The SN65HVD101RGBT is the IO-Link physical layer for a device node: the sensor end, not the master end. It converts the 24 V single wire IO-Link signal on the CQ pin into logic levels on RX and takes TX from the local controller, with a driver that can be configured as push pull, high side or low side for the older three wire SIO mode. The supply range is 9 V to 36 V and the line is tolerant to 50 V peaks, which covers the transients a factory floor cable produces.

The 101 member is the one with the integrated linear regulator. It takes the IO-Link L+ rail and produces 3.3 V or 5 V for the PHY and for a local controller, so a small sensor can run from the same two wires that carry the data without a second supply. The 102 member drops that regulator and runs from an external rail, which is the choice when the node already has a 3.3 V supply and the heat budget is tight.

Key data for the SN65HVD101RGBT

RoleIO-Link device PHY with an integrated 3.3 V or 5 V linear regulator from the L+ rail
Supply9 V to 36 V on L+, tolerant to 50 V peak line voltage, reverse polarity protected
DriverCQ output configurable as push pull, high side or low side for SIO mode, current limit 60 mA to 130 mA on the default setting and up to 480 mA with an external set resistor
ProtectionOvercurrent limit, overtemperature shutdown, power good and current limit indicators, remote wake up detection
Current drawQuiescent supply current 1 mA to 2 mA on the 102 member, 1.3 mA to 3 mA dynamic with the driver disabled
ThresholdsInput high 10.5 V to 13 V, input low referenced to L+ through the internal divider, so the threshold follows the rail rather than a fixed voltage

Body, marking and reel data

BodyRGB, VQFN 20 at 4.00 mm by 3.50 mm, the small package that fits behind an M12 connector
Reel250 pieces on a small reel for the T suffix row, 1000 pieces on a large reel for the R suffix and the .B row
MarkingHVD102 on the SN65HVD101RGB rows, which is the die shared by both members and reads as a mismatch against the order code
HandlingMoisture level 2, 260 C peak, 1 year floor life, so the reel has a clock on it once the bag is opened
TemperatureMinus 40 C to 105 C on the published rows, wider than the 85 C of most interface parts

Where an IO-Link PHY changes a sensor build

An IO-Link sensor has to survive a shorted cable, a reversed supply and a hot plug into a live master port. Handling those in discrete parts takes a comparator chain, a current sense resistor, a MOSFET and a handful of clamps. The SN65HVD101RGBT puts the driver, the limit, the thermal shutdown and the diagnostics into one 4 mm by 3.5 mm body, and it reports the fault through the SC and PWR_OK pins so the controller can log a cause instead of a symptom.

The wake up path matters for battery free nodes. In sleep the PHY watches the CQ line and the EN pin and wakes the controller when the master starts a session. Because the regulator is inside the 101, the controller can be powered from the same L+ pair and the whole node can sit at microamp level until the master polls it.

Questions we get when this code is on a BOM

The first question is about the current limit setting. The datasheet publishes a default window of 60 mA to 130 mA and shows a second window up to 480 mA when an external resistor is fitted on RSET. The vendor application note works an example at 4 kohm for a 250 mA limit, and the resistor has to be placed close to the pin with its own ground return. A node that trips on inrush usually needs a higher limit and a longer blanking time, not a bigger regulator.

The second question is about the marking. The SN65HVD101RGBT rows print HVD102 on the package, because both members share a die. A receiving inspection that compares the printed code to the order code will raise a mismatch every time, so we put the explanation on the offer and on the packing list rather than leaving it to the line to discover.

How SUPERB supports this line item

We quote the SN65HVD101RGBT with the reel size, the moisture level and the marking note attached, because the marking mismatch is the most common incoming inspection query on this family. Customers building IO-Link nodes can combine the PHY with the connector, the TVS diode and the EMC filter through our one stop BOM sourcing route.

Where a node is being moved from a proprietary three wire interface to IO-Link, our pin to pin cross reference page explains how we compare the driver configuration pins before proposing a board change.