Contact Us

SN65CML100DGKR

Brand: Texas Instruments
Texas Instruments SN65CML100DGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65CML100DGKR — Power Management & Signal Chain | Superb Automation

SN65CML100DGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65CML100DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65CML100DGKR: a 1.5 Gbps LVDS or LVPECL to CML translator and repeater

The SN65CML100DGKR takes an LVDS, LVPECL or CML signal in and drives a CML signal out at rates up to 1.5 Gbps. It is a single channel device in an 8 pin VSSOP body, and its job is level translation and line repeating: a receiver front end that only speaks CML can be fed from an LVDS backplane, or a CML clock can be repeated across a card without the loss of a passive split.

The output drives 50 ohm or 25 ohm loads tied to a 1.8 V, 2.5 V or 3.3 V termination supply, and because the driver is current mode it can often be connected to the load without coupling capacitors. The input side tolerates a common mode range of 0 V to 4 V with 25 mV of hysteresis, so an LVDS driver, an LVPECL driver and a CML driver all connect directly.

Key data for the SN65CML100DGKR

RateUp to 1.5 Gbps, 622 MHz central office clock distribution is the published application
JitterTotal jitter below 70 ps, part to part skew 100 ps maximum, propagation delay 800 ps maximum
InputLVDS, LVPECL and CML compatible, common mode 0 V to 4 V, 25 mV of threshold hysteresis, 100 mV threshold
Supply3.0 V to 3.6 V on VCC, 9 mA typical and 12 mA maximum, termination rail 1.8 V, 2.5 V or 3.3 V
ReferenceVBB pin at 1.89 V to 2.01 V, which tracks the supply, for single ended LVPECL inputs, 400 uA limit
TemperatureMinus 40 C to 85 C, power rating 425 mW in the DGK body at 25 C ambient

Body, marking and reel data

BodyDGK, VSSOP 8 at 3.00 mm by 3.00 mm, the small body that suits a repeater placed mid card
Reel2500 pieces on a large reel for SN65CML100DGKR and for the G4 row, carrier tape 12.4 mm
MarkingNWB on both active rows, so the reel label carries the distinction rather than the printed code
HandlingMoisture level 1, 260 C peak, unlimited floor life
Tape noteThe tape and reel table prints SOIC against the DGKR row even though the body is VSSOP DGK, a labelling slip in the vendor file rather than a second package

Where a CML repeater earns its place

Backplane links that leave a card in LVDS often arrive at a line card that runs CML optics. Putting a translator at the entry point lets the card use one signalling family after the connector, and it also restores the eye that the connector and the stub consumed. The 1.5 Gbps ceiling covers 1.25 Gbps Ethernet, 1.0625 Gbps Fibre Channel and the 622 MHz clock trees that still run in telecom shelves.

The VBB reference is the detail that makes single ended LVPECL inputs possible. When one side of the differential pair is unused, it is tied to VBB and decoupled with a 0.01 uF capacitor, and the current drawn from that pin has to stay under 400 uA. Builders who forget the current limit and tie a terminated 50 ohm line to VBB will pull the reference off centre and close the eye without any obvious fault.

Questions we get when this code is on a BOM

Most questions are about termination. The driver expects the load to be returned to a termination rail, and that rail can be 1.8 V, 2.5 V or 3.3 V while VCC stays at 3.3 V. A board that already has a 2.5 V rail can use it, a board that only has 3.3 V can still terminate to 3.3 V with 50 ohm resistors, and the part works either way. What it cannot do is drive a load that is returned to ground. Where the termination rail comes from a switcher, its ripple appears directly on the output common mode, so the decoupling at the termination network matters as much as the decoupling at VCC. A 0.1 uF capacitor at each termination resistor is the usual starting point.

The second question is whether this device can be used as a redriver with equalisation. It cannot: the SN65CML100DKGR repeats and translates, and the jitter budget assumes a clean input eye. Where the trace loss is large enough to need equalisation, the right answer is a different device and a different conversation, and we say so early rather than after two prototype spins.

How SUPERB supports this line item

We supply the SN65CML100DGKR as a catalogue line for telecom and test equipment builds, and we check the reel row before quoting because both active rows carry the same marking. Customers moving a link from LVDS to CML can use our RF component sourcing route to place the translator, the termination resistors and the coupling capacitors on one order.

When an engineering team sends a full BOM for a line card, the one stop BOM sourcing service covers the high speed interface parts together with the passives, which is where most of the lead time problems sit.