SN6507DGQRQ1
Product Specifications
SN6507DGQRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The SN6507DGQRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
SN6507DGQRQ1: a 36 V push pull driver with duty cycle control
The SN6507DGQRQ1 is a push pull transformer driver with a 3 V to 36 V input range, 60 V of input tolerance, and two 0.5 A switches in a 10 pin HVSSOP with a thermal pad. It is the high voltage member of the family: where the SN6505 stops at 5.5 V and drives 1 A, this part reaches 36 V and drives 0.5 A, which is the combination that an industrial 24 V bus or a 48 V rail needs for an isolated gate driver supply.
The feature that separates it from a fixed 50 per cent push pull stage is duty cycle control. By modulating the duty cycle against the input voltage, the part holds the isolated output steady over a wide input range without a post regulator, which removes a linear regulator and its loss from the isolated side. The switching frequency is programmable from 100 kHz to 2 MHz, and the device adds spread spectrum clocking, slew rate control, adjustable under voltage lockout, over voltage lockout, programmable current limit and thermal shutdown.
Key data for the SN6507DGQRQ1
| Input | 3 V to 36 V operating with tolerance to 60 V, which covers a 24 V industrial bus and a 48 V rail with derating |
| Switches | Two 0.5 A N channel switches driving the transformer out of phase, with a programmable current limit |
| Frequency | Programmable from 100 kHz to 2 MHz with an external clock synchronisation option |
| Regulation | Duty cycle control against the input voltage, which holds the isolated output without a post regulator over a wide input range |
| Protection | Adjustable under voltage lockout, over voltage lockout, programmable over current, thermal shutdown, break before make and a programmable soft start |
| Temperature | Minus 55 C to 125 C, with a thermal pad on the 10 pin body for the 0.5 A switch loss |
Body, marking and reel data
| Body | DGQ, 10 pin HVSSOP with an exposed thermal pad, which is the reason the part can carry 0.5 A per switch in a small outline |
| Grade | Q1 automotive suffix; the library document SLLSFM0A is the base revision, so the automotive release data comes from the Q1 document |
| Reel | R suffix is the large reel; the thermal pad has to be soldered to a copper area, not left floating |
| Pins | EN and UVLO share a pin, SS and ILIM share a pin, and CLK is separate, so the soft start and the current limit are set by the same resistor network |
| Document | SLLSFM0A dated March 2022 and revised June 2022 |
Where a 36 V push pull driver fits
An isolated gate driver for an IGBT or a silicon carbide switch needs a floating 15 V to 20 V supply, and that supply is referenced to the emitter of the switch, which moves by hundreds of volts. The usual answer is a transformer driven from the controller side, and the driver has to work from whatever rail the controller has. On a 24 V industrial drive that rail is 24 V, and on a 48 V system it is 48 V, both of which are above the 5.5 V ceiling of the smaller family member.
Duty cycle control is what keeps the isolated voltage steady without a regulator. A fixed 50 per cent push pull stage delivers a voltage proportional to the input, so a 24 V bus that varies from 18 V to 30 V produces an isolated rail that varies by 60 per cent, which a gate driver cannot accept. The SN6507 measures the input and adjusts the duty cycle, so the isolated rail stays within a window that the driver can use, and the part does that without a feedback winding on the transformer.
The 100 kHz to 2 MHz range is the other lever. A low frequency keeps the switching loss down and allows a larger transformer; a high frequency shrinks the transformer but raises the loss in the 0.5 A switches. For a gate driver supply the transformer is usually small and the frequency is set high enough to keep it small, while the slew rate control keeps the emissions inside a limit. Our power management cross reference lists the isolated supply drivers by input range and switch current, and the component lead time solutions note covers what to do when the automotive grade is quoted long and the industrial grade is in stock.
Buyer questions on the SN6507DGQRQ1
Can the output be regulated without a feedback winding? Yes, the duty cycle control uses the input voltage and the known transformer ratio, which holds the output within a window rather than to a precision. A rail that needs 1 per cent still needs a post regulator.
Is the 60 V tolerance a continuous rating? It is a transient tolerance, and the operating range is 3 V to 36 V. A 48 V rail needs a check against the transient, and a 60 V bus is outside the operating range.
Why do the soft start and the current limit share a pin? Because both are set by a resistor and a capacitor from the same node, which saves a pin on a 10 pin body. The value has to satisfy both functions at once, so the two requirements are calculated together.
Availability and ordering notes
SN6507DGQRQ1 is the automotive grade of the 36 V push pull driver in the 10 pin HVSSOP. The industrial code without the Q1 suffix is a separate line item, and the automotive release is a separate document from the base revision in our library. Because the part drives a transformer that is chosen for the frequency and the ratio, a quotation should include the transformer recommendation rather than the driver alone.