Contact Us

SN6505BDBVR

Brand: Texas Instruments
Texas Instruments SN6505BDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN6505BDBVR — Power Management & Signal Chain | Superb Automation

SN6505BDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN6505BDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN6505BDBVR: a 420 kHz push pull transformer driver for isolated supplies

The SN6505BDBVR is a push pull transformer driver in a 6 pin SOT-23 that turns a 2.25 V to 5.5 V input into an isolated supply through a small centre tapped transformer. The B version switches at 420 kHz, against 160 kHz on the A version, which halves the transformer size at the cost of slightly higher switching loss. The output drive is 1 A at a 5 V supply, with 0.25 ohm maximum on resistance at 4.5 V.

The reason this part exists is isolation without a module. An isolated CAN, RS-485 or RS-232 port needs a floating supply for the transceiver side, and a module costs more and takes more height than a driver plus a transformer. The SN6505B adds spread spectrum clocking and slew rate control to keep the emissions low, which is what allows a small transformer to pass an emissions limit without a shield.

Key data for the SN6505BDBVR

TopologyPush pull driver for a centre tapped transformer, two internal N channel switches switching out of phase
Input2.25 V to 5.5 V, with 1 A of output drive at 5 V and 0.25 ohm maximum on resistance at 4.5 V
Frequency420 kHz internal oscillator on the B version against 160 kHz on the A version, plus an external clock input for synchronisation
EmissionsSpread spectrum clocking and pin selectable slew rate control, which are the two features that let a small transformer meet a limit
Protection1.7 A current limit, under voltage lockout, thermal shutdown and break before make, plus a soft start that limits inrush into a large output capacitor
Supply and temperatureUnder 1 uA in shutdown, minus 55 C to 125 C, which is wider than most of the logic around it

Body, marking and reel data

BodyDBV, 6 pin SOT-23, the only body this family ships in
ReelR suffix is the large reel; the 6 pin body is small enough to sit beside the transformer without a separate keep out
TransformerA centre tapped isolation transformer with a 1 to 1 or 1 to 1.5 ratio is the usual match; the turns ratio sets the isolated voltage and the driver sets the current
Soft startLimits the inrush that a large output capacitor would otherwise draw through the transformer and the switches
DocumentSLLSEP9I dated September 2015 and revised August 2023, a long lived part with a current revision

Where a push pull driver beats an isolated module

An isolated DC to DC module is a finished part with a case, a pinout and a datasheet that promises a regulation figure. A driver plus a transformer is three parts and a footprint, and it is chosen when the height, the cost or the isolation voltage has to be controlled rather than accepted. The SN6505B at 420 kHz allows a transformer of a few millimetres, which is the height that a module cannot reach.

The push pull topology has a property that matters for emissions: the two switches drive the transformer in opposite directions, so the flux in the core cancels and the transformer does not saturate from a DC bias. That is why the topology can run at a fixed 50 per cent duty cycle without a feedback loop and still deliver a usable output. Regulation comes from a linear regulator on the isolated side, or from a shunt reference, which is acceptable when the load is a transceiver that draws a constant current.

The emissions features are the difference between a board that passes and one that needs a shield. Spread spectrum clocking moves the switching energy across a band so the peak at 420 kHz is lower, and slew rate control reduces the high frequency content of the switching edge. Both are pin selectable, so a board that has margin can turn them off to gain efficiency, and a board that is close to a limit can turn them on. Our power management cross reference lists the isolated supply options by input range and switch current, and the CAN bus transceiver selection note covers the transceivers that this supply usually powers, including the current each one draws.

Buyer questions on the SN6505BDBVR

Does the output need a regulator? For a transceiver, usually yes in the form of a small linear regulator or a shunt reference, because the push pull stage is not closed loop and its output falls with load.

Can two drivers be synchronised? Yes, the clock pin accepts an external clock, and the document describes synchronising several devices so their harmonics do not beat against each other.

Is the A version a drop in for the B? The body and the pinout are the same, and only the internal oscillator frequency differs, so the board accepts either. The transformer has to be re checked because it was chosen for one frequency.

Availability and ordering notes

SN6505BDBVR is the 420 kHz member in the 6 pin SOT-23, and SN6505ADBVR is the 160 kHz sibling in the same body. Because the part is a long lived line with a 2023 revision, both versions are usually available, and the choice between them is a transformer decision rather than a supply decision. A customer who is second sourcing an isolated supply should be asked for the transformer as well as the driver, since the two are specified together.