Contact Us

SN6505AQDBVRQ1

Brand: Texas Instruments
Texas Instruments SN6505AQDBVRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN6505AQDBVRQ1 — Power Management & Signal Chain | Superb Automation

SN6505AQDBVRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN6505AQDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN6505AQDBVRQ1: automotive transformer driver that builds an isolated rail from 5 V

SN6505AQDBVRQ1 is a push pull driver for a centre tapped transformer in a six pin SOT-23, built so a small isolated supply can sit next to a CAN, RS-485 or gate drive port instead of a separate supply module in a SOT-23 body of 6 pins. It works from 2.25 V to 5.5 V, switches 1 A at 5 V and 0.75 A below 2.8 V, holds the switch on resistance to 0.16 ohm typical and 0.25 ohm maximum at 4.5 V, and clamps at 1.42 A minimum. The A member of the family runs at 160 kHz and the B member at 420 kHz, both with spread spectrum clocking and slew rate control, and the part falls to 0.1 uA typical with the enable pin low. Break before make is 115 ns on the A member and 90 ns on the B, soft start reaches 90 per cent in 4.25 ms typical, and the junction to ambient figure in the DBV body is 137.7 degrees per watt.

Order code and package

SN6505AQDBVRQ1automotive grade of the 160 kHz member in the DBV body, six pins, 2.90 mm by 1.60 mm. The document used for this page prints the industrial strings and names SN6505A-Q1 and SN6505B-Q1 as other qualified versions, so the reel size and the packing for the Q1 string were left unconfirmed rather than copied from an industrial row
SN6505ADBVRindustrial 160 kHz member, 3000 pieces on a large reel, moisture level 1 with unlimited floor life on the A row, minus 55 to plus 125 degrees, marking 650A or 65AQ
SN6505ADBVTthe same body on a 250 piece small reel, which is the row a prototype or a repair order comes from
SN6505BDBVRthe 420 kHz member in the same six pin body, 3000 pieces on a large reel, marking 650B or 65BQ. The pinout is identical and only the internal oscillator changes
print notethe addendum prints a 3000 piece large reel against a part number whose T suffix means a small reel, and a 250 piece small reel against a row with no part number at all, so the quantity column has to be read per row and the reel count confirmed on the label

Electrical parameters that decide the application

Supply2.25 V to 5.5 V on the primary side. A 5 V rail gives the full 1 A of switch current, a 3.3 V rail works with the same figure, and a 2.5 V rail still runs but the switch current ceiling falls
Switch current1 A per switch above 2.8 V and 0.75 A below it, which is the derating a 2.5 V board has to read before it sizes a transformer for 1 A
On resistance0.16 ohm typical and 0.25 ohm maximum at 4.5 V and 1 A, 0.19 and 0.31 ohm at 2.8 V, 0.21 and 0.45 ohm at 2.25 V with 0.5 A. At 1 A the worst case drop across one switch is a quarter of a volt and the loss is a quarter of a watt, which is what decides the copper and the thermal pad
Switching frequency160 kHz on the A member, printed as 138 kHz minimum and 203 kHz maximum, against 420 kHz on the B member with 363 kHz minimum and 517 kHz maximum. The B member suits a smaller transformer and pushes the harmonics higher
External clockthe CLK pin accepts 100 kHz to 600 kHz on the A member and 100 kHz to 1600 kHz on the B, which lets several drivers be locked together or the harmonics moved away from a receiver band. An invalid clock hands control back to the internal oscillator within 10 to 25 microseconds
Current limit1.42 A minimum, 1.75 A typical and 2.15 A maximum above 2.8 V, folding to 0.65 A minimum below 2.8 V, so a shorted secondary pulls a bounded current rather than the full rail
Under voltage lockout2.25 V rising and 1.7 V falling with 0.3 V of hysteresis, which releases the switches on a rail that sags rather than letting them run at a gate voltage with no drive
Shutdown current0.1 uA typical with the enable pin low, below 1 uA over temperature, and the leakage on the two switch pins also falls to 0.1 uA so an unused driver does not load the transformer
Break before make115 ns on the A member and 90 ns on the B, the gap that stops both switches conducting through the centre tap at the same instant
Soft start1 ms minimum to 8 ms maximum with 4.25 ms typical across a 40 uF load, and a delay of 3.5 ms to 18 ms with 8.5 ms typical from power up. This is the feature that stops a large isolated capacitor bank from tripping the fuse on the primary rail
Thermaljunction to ambient 137.7 degrees per watt in the six pin body, thermal shutdown at 168 degrees and release at 150 degrees, so a driver held into a short folds back and then parks itself
Temperatureminus 55 to plus 125 degrees on the printed rows, which is wider than the 125 degree ceiling most six pin drivers carry and the reason the part appears in automotive and outdoor equipment

Family variants and how they differ

A against Bthe same die with a 160 kHz or a 420 kHz oscillator. The B member allows a smaller transformer for the same delivered power, and it moves the switching energy into a band that a nearby receiver may care about
Q1 against industrialthe automotive string is qualified separately and carries its own document. The electrical behaviour is the same family behaviour, but the packing, the marking and the process paperwork are not printed in the industrial addendum
Against SN6501the earlier driver has no spread spectrum, no soft start and a lower current clamp. A board that already carries the SN6501 can usually take this part, but the transformer and the input capacitor have to be checked because the switching profile is not the same
Against an isolated modulea ready made isolated converter removes the transformer choice and the EMI work at the cost of board area and price per watt. At the 1 W level this part plus a small transformer is usually the cheaper route
Against a flyback controllera flyback regulates with an optocoupler or a third winding. This part is an open loop driver, so the isolated rail is unregulated and its load regulation comes from the transformer ratio, the switch resistance and the rectifier drop

Points to check before this part goes on a BOM

The output of this circuit is not regulated, and that surprises buyers who read 1 A and expect a 5 V module. The secondary voltage follows the turns ratio and falls with load because of the switch resistance, the transformer winding resistance and the rectifier drop. A rail that has to hold a few per cent under load needs a low dropout regulator after the rectifier, or a feedback path that this part does not provide. Any offer that promises a regulated isolated rail from a two switch driver is describing a board and not the silicon.

The 1 A figure belongs to a supply above 2.8 V. Below that the switch current is limited to 0.75 A by the recommended operating conditions, so a 2.5 V board that sizes the transformer for 1 A is working outside the printed condition. The on resistance also rises at the lower rail, 0.45 ohm maximum at 2.25 V, which turns into a larger voltage drop at the same current.

The automotive string is the reason this page exists, and the document in hand does not print its reel. The industrial rows show 3000 pieces on a large reel and 250 on a small reel, and those figures cannot be carried across as a promise for the Q1 body. A quotation for SN6505AQDBVRQ1 should state the packing as confirmed at order time rather than assume the industrial reel, because an automotive customer usually needs the label and the certificate to match the drawing.

Spread spectrum and slew rate control are fixed inside the part and are not adjustable from outside. The A member switches with a 48 V per microsecond voltage slew and an 11 A per microsecond current slew, the B member with 152 V per microsecond and 41 A per microsecond. That difference is why the B member is chosen when the transformer has to be small, and why the A member is chosen when a narrow band receiver sits on the same board.

Break before make and soft start both interact with the leakage inductance of the transformer. A transformer with high leakage produces a larger flyback spike when a switch turns off, and the clamp or the switch rating has to absorb it. The soft start ramp controls the current into the secondary capacitor, so a very large capacitor bank lengthens the ramp and the upstream supply has to hold its rail for that whole time.

The enable pin is not a hard logic input in the sense of a microcontroller port with a weak pull down. It has 10 to 20 uA of leakage and thresholds at 0.7 times the rail and 0.3 times the rail, so a pull down resistor has to be small enough to hold the pin below the low threshold with that leakage across the full temperature range. A board that leaves the pin floating may find the driver switching when the controller is in reset.

Where the isolated rail comes from

Isolated CAN and RS-485 ports are the largest use. The bus side of an isolated transceiver needs a few tens of milliamps at 5 V, and this driver plus a small centre tapped transformer delivers it from the logic rail without a second supply. The 420 kHz member exists for exactly that case, because the transformer can be a small surface mount part.

Gate drive supplies for IGBT and silicon carbide bridges use the same circuit at a higher isolation level, often one driver per high side switch. Medical sensor front ends use it where the barrier has to be certified and the current is small. In all three cases the load is light, the isolation is the point, and the regulation is handled downstream.

What the order code decides

The string reads SN6505A for the 160 kHz member, Q for the automotive qualification, DBV for the six pin SOT-23 body and R for the reel. No character in the string selects the switching frequency, the current limit or the temperature range, because those belong to the device number, so a purchase order that changes A to B by hand is buying a different oscillator and possibly a different transformer.

The reel letter matters at the line level. A 3000 piece reel feeds a placement machine without a reload, a 250 piece reel covers a pilot build. Mixing the two on one purchase order is normal, but the line has to know which is which before the feeder is loaded.

Where this order code fits

Isolated CAN and RS-485 ports, gate drive supplies for motor bridges, medical front ends and any board that has to move a few hundred milliwatts across a barrier without a second rail on the isolated side. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is the Q1 reel printed in this document? No. The addendum lists the industrial SN6505A and SN6505B rows and names SN6505A-Q1 and SN6505B-Q1 as other qualified versions. The automotive packing has to be confirmed against the automotive document or the label before a quotation states a quantity.

Does it regulate the isolated output? No. It is an open loop push pull driver. The secondary voltage follows the turns ratio and drops with load, so a regulated rail needs a low dropout regulator after the rectifier.

What transformer does it want? A centre tapped transformer with a primary that suits 2.25 V to 5.5 V and a secondary sized for the rail and the current. The A member at 160 kHz needs more core than the B member at 420 kHz for the same delivered power.

How much current does it use when disabled? 0.1 uA typical and below 1 uA over temperature, with the switch pin leakage also at 0.1 uA. That is low enough that a battery fed product can leave the driver disabled for years.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.