OPA725AIDBVT
Product Specifications
OPA725AIDBVT
Texas Instruments — Power Management & Signal Chain
Product Overview
The OPA725AIDBVT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
OPA725AIDBVT: 20 MHz 12 V CMOS operational amplifier with 30 volts per microsecond in a 5-pin SOT-23
OPA725AIDBVT is a 12 V CMOS operational amplifier with 20 MHz of gain bandwidth, 30 volts per microsecond of slew and 5.5 milliamps per channel of supply current in a SOT-23 body of 5 pins. The AIDBVT suffix is the industrial grade in the 5-pin SOT-23 on a 250 piece tape. The part runs from a 4 V to 12 V supply, reaches 20 MHz of gain bandwidth with 30 volts per microsecond, draws 5.5 milliamps per channel maximum, holds offset to 1.2 millivolts typical and 3 millivolts maximum, and produces 0.0003 percent total harmonic distortion plus noise, with a shutdown variant in the same family that drops to 6 microamps per channel.
Order code and package
| Order code | OPA725AIDBVT |
| Function | 12 V CMOS operational amplifier, 20 MHz class |
| Package | SOT-23, 5 pins, body code DBV, 250 piece tape |
| Supply range | 4 V to 12 V total, plus or minus 2 V to plus or minus 6 V |
| Supply current | 5.5 milliamps per channel maximum |
| Gain bandwidth | 20 MHz |
| Slew rate | 30 volts per microsecond |
| Offset | 1.2 millivolts typical, 3 millivolts maximum |
| Voltage noise | 10 nanovolts per root hertz at 10 kHz, 6 nanovolts per root hertz at 100 kHz |
| Distortion | 0.0003 percent total harmonic distortion plus noise |
| Shutdown | the OPA726 in the same family drops to 6 microamps per channel |
| Datasheet | OPA725, OPA726 family document |
Electrical parameters that decide the application
| Flicker noise | 10 microvolts peak to peak from 0.1 to 10 Hz |
| Input | CMOS, with picoamp class bias current |
| Output | rail to rail on a 12 V supply, driving a converter or a filter |
| Common-mode rejection | high, quoted with the supply rejection and open loop gain as a group |
| Packages | SOT-23 and SOIC in the family, with the shutdown option in a 6-pin body |
| Operating range | industrial, with the junction limit set by the SOT-23 body |
Points to check before this part goes on a BOM
3 millivolts of maximum offset is not a precision specification, and on a 12 V range it is 1 part in 4000, which is 12 bits of error. The part is aimed at signal chains where the swing and the distortion matter more than the DC accuracy, and the 0.0003 percent distortion figure is the one the marketing rests on. A DC coupled 16 bit channel on a 12 V rail needs a different amplifier in front of it.
20 MHz of gain bandwidth at a gain of 10 gives 2 MHz of closed loop bandwidth, and 30 volts per microsecond at a 10 V peak to peak signal gives 0.95 MHz. At the top of the swing the slew rate limits first, at a tenth of the amplitude the gain limits first, so the usable bandwidth depends on the amplitude by a factor of two across the 12 V range. That crossover is the number to calculate for a specific application rather than quoting the 20 MHz headline.
6 nanovolts per root hertz at 100 kHz is a low noise density for a CMOS input, and 10 nanovolts at 10 kHz shows the flicker contribution falling away above 10 kHz. Over a 1 MHz band the integrated noise is about 6 microvolts RMS, which is 2.5 bits on a 12 V range at 12 bits. For an audio band of 20 kHz the integrated noise is under a microvolt and the part is quiet enough for a line stage.
The supply floor of 4 V is the constraint that catches people. This is not a 3.3 V part: at 3.3 V it is outside the specified range, and the rail-to-rail output that makes it useful on 12 V cannot be assumed on a 3.3 V rail. A board that mixes 12 V analog and 3.3 V digital has to keep this amplifier on the 12 V rail and level shift afterwards, or use a 5.5 V part for the 3.3 V section.
5.5 milliamps per channel maximum in a 5-pin SOT-23 is 33 milliwatts, and the package thermal resistance is high enough that four channels in the same board area need spacing. The shutdown variant matters here: 6 microamps per channel in shutdown turns a four channel board from 132 milliwatts into 24 microwatts, which is the difference between a battery product that lasts a month and one that lasts a year.
10 microvolts peak to peak from 0.1 to 10 Hz is the flicker floor of a CMOS process without chopping, and on a 12 V range it is 0.5 of a 20 bit bit. A channel that needs better than that at DC has to chop, and chopping at 20 MHz is not available in this catalogue. The practical rule is that this part serves AC and mid-resolution DC work and a zero-drift part serves the low frequency end, with the two stages split by a filter.
Where this order code fits
12 V industrial signal chains, portable instrument front ends, active filters, audio stages and any board that needs more than 5 V of swing with CMOS input current on a small footprint use this part. The 12 V rail is what separates it from the 5.5 V rail-to-rail families and the reason it turns up in industrial rather than consumer boards. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the ADC DAC Cross Reference page.
Questions buyers ask
Can the OPA725 run from a 3.3 V rail? No. The specified supply range starts at 4 V, so 3.3 V is outside it. A 3.3 V board needs a rail-to-rail part specified down to 1.8 V or 2.2 V.
What does the shutdown option buy? The OPA726 in the same family drops to 6 microamps per channel, against 5.5 milliamps. In a four channel duty cycled board that is the difference between 132 milliwatts and 24 microwatts.
Is 20 MHz available at full output swing? No. 30 volts per microsecond limits a 10 V peak to peak signal to about 0.95 MHz, while the 20 MHz gain bandwidth limits a small signal at a gain of 10 to 2 MHz.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.