Contact Us

OPA365AID

Brand: Texas Instruments
Texas Instruments OPA365AID is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA365AID — Power Management & Signal Chain | Superb Automation

OPA365AID

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA365AID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA365AID: 50 MHz zero-crossover rail-to-rail CMOS operational amplifier in an 8-pin SOIC

OPA365AID is a 50 MHz rail-to-rail CMOS operational amplifier whose input stage avoids the crossover step that normally comes with a rail-to-rail input in a SOIC body of 8 pins. The AID suffix is the 8-pin SOIC body. The part runs from 2.2 V to 5.5 V, reaches 50 MHz of gain bandwidth with 25 volts per microsecond of slew, draws 4.5 milliamps, and holds offset to 100 microvolts typical and 200 microvolts maximum with a 1 microvolt per degree drift. The input is a zero-crossover arrangement, so the common-mode rejection does not collapse when the signal passes through mid-supply.

Order code and package

Order codeOPA365AID
Functionzero-crossover rail-to-rail input and output CMOS operational amplifier
PackageSOIC, 8 pins, body code D
Supply range2.2 V to 5.5 V
Supply current4.5 milliamps
Gain bandwidth50 MHz
Slew rate25 volts per microsecond
Offset100 microvolts typical, 200 microvolts maximum
Offset drift1 microvolt per degree
Input bias current0.2 picoamps typical, 10 picoamps maximum
Power-supply rejection10 microvolts per volt
DatasheetOPA365, OPA2365 family document

Electrical parameters that decide the application

Channel separation0.2 microvolts per volt at DC
Input stagezero crossover, so no mid-supply step in the input offset
Outputrail to rail, capable of driving a switched capacitor input
Bias current over temperaturepicoamp class, so megohm sources are usable
Unity gain stabilitystable at a gain of one, with 25 volts per microsecond available
Settlingfast enough to follow a 12 bit converter's acquisition window at 1 MSPS
Operating rangeindustrial and automotive grade depending on the order code suffix

Points to check before this part goes on a BOM

Zero crossover is the reason to pay for this part. A conventional rail-to-rail input uses two pairs, one for the low common-mode range and one for the high, and the offset jumps by a few hundred microvolts as the signal crosses between them. In a buffer feeding a 16 bit converter that step appears as a code jump at mid-scale, and in an audio path it appears as crossover distortion. This part removes the step, so the 200 microvolt offset applies across the whole input range.

200 microvolts on a 16 bit converter at 5 V is 2.6 bits, and the 1 microvolt per degree drift over 125 degrees adds 125 microvolts, which is another 1.6 bits. That is respectable for a 50 MHz part and still not a calibration free 16 bit channel. The point of the zero-crossover stage is that the error is stable and continuous rather than that it is small, and a single point calibration removes it cleanly.

25 volts per microsecond at a 2 V peak to peak signal allows about 2 MHz, while 50 MHz of gain bandwidth allows 5 MHz at a gain of 10. The two limits are close enough that a filter running at 1 MHz uses most of the slew rate at 2 V peak to peak, and a 4 V peak to peak signal at the same frequency needs 12.6 of the 25 volts per microsecond available. There is margin at 1 MHz and none at 4 MHz.

4.5 milliamps at 3.3 V is 14.9 milliwatts, so a dual in the same family is 30 milliwatts. For a 50 MHz part that is low, and it is the reason this amplifier turns up in portable instruments where a 20 MHz bipolar part would have been the only choice a decade ago. The current does not change with the output load in the quiescent figure, so the output stage current has to be added when a cable is driven.

10 microvolts per volt of supply rejection means 100 millivolts of ripple on a 3.3 V rail arrives as 1 microvolt at the input, half the offset. That is good enough to run from a switching regulator without a post regulator, which is what a portable instrument wants, but the rejection is a DC figure and the switching frequency behaviour has to be checked on the bench with the actual inductor and wiring of the supply.

10 picoamps of maximum bias current means a 1 megohm source adds 10 microvolts, and a 10 megohm source adds 100 microvolts, which is half the offset. That is why the part suits photodiode and high impedance sensor work despite being a 50 MHz amplifier: the input stage was chosen for bias current and for linearity, and the bandwidth came along with the process rather than being the only objective.

Where this order code fits

Fast 12 and 16 bit converter drivers, active filters, photodiode and sensor buffers and 3.3 V signal chains use this part because the zero-crossover input keeps distortion low while the signal sweeps the full rail-to-rail range, which is exactly what a single-supply converter input does. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Amplifier Cross Reference page.

Questions buyers ask

What does zero crossover mean in practice? It means the input offset does not step when the common-mode voltage passes mid-supply. A conventional rail-to-rail input swaps between two pairs there and produces a small discontinuity, which shows up as distortion or a code jump near mid-scale.

Can this part drive a 16 bit converter directly? Yes with a single point calibration. The 200 microvolt offset is 2.6 bits at 16 bits on 5 V and the drift adds 1.6 bits over the industrial range, so the error is continuous and removable rather than random.

What is the advantage over a 20 MHz bipolar amplifier? Lower bias current, rail-to-rail input and output on a single supply, and 4.5 milliamps of supply current at 50 MHz, at the cost of a larger offset than a precision bipolar part.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Medical Device Components page sets out the checks that keep a substitute from failing on the bench.