Contact Us

OPA130UA

Brand: Texas Instruments
Texas Instruments OPA130UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA130UA — Power Management & Signal Chain | Superb Automation

OPA130UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA130UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA130UA: FET input precision operational amplifier with 1 MHz bandwidth in an 8-pin SOIC

OPA130UA is a single FET input operational amplifier with 20 picoamp bias current, 1 millivolt offset and 530 microamps of supply current in a SOIC body of 8 pins. The OPA130 is the single version of a FET input family that trades bandwidth for bias current and quiescent current: 1 MHz gain bandwidth, 2 volts per microsecond, 530 microamps per amplifier, 20 picoamps of maximum input bias current and 1 millivolt of maximum offset. The input stage is cascoded, which holds the bias current flat across the common mode range, and the part is stable at unity gain with capacitive loads.

Order code and package

Order codeOPA130UA
Functionsingle FET input precision operational amplifier
PackageSOIC, 8 pins, body code D
Supply rangeplus or minus 2.25 V to plus or minus 18 V
Gain bandwidth1 MHz
Slew rate2 volts per microsecond
Input bias current20 pA maximum, about 5 pA typical
Offset voltage1 mV maximum
Quiescent current530 microamps per amplifier
Open loop gain123 dB with a 10 kilohm load
DatasheetSBOS053 revision B, May 1998 revised May 2024

Electrical parameters that decide the application

Common mode rejection90 dB minimum
Input voltage noise18 nanovolts per root hertz at 100 Hz
Bias current over common modeheld flat by the cascode input stage
Unity gain stabilityyes, with capacitive load capability
Phase inversionnone, the family is specified free of it
Overload recoveryspecified, with no phase inversion on overdrive
Temperature grademinus 40 to plus 85 C for the single, dual and quad
Package options8-pin SOIC single and dual, 14-pin SOIC quad
Input protectiondiodes and a cascode stage
FamilyOPA130, OPA2130 and OPA4130 share the specification

Points to check before this part goes on a BOM

The 20 picoamp limit is the whole point of the part, and it only pays when the source impedance is high. Into a 1 megohm source it is 20 microvolts, which is small against the 1 mV offset, but into 100 megohm it is 2 mV, and into 1 gigohm it is 20 mV. Above about 10 megohm this amplifier is the right choice and below it a bipolar part with better noise wins.

1 MHz of gain bandwidth at a gain of 100 leaves 10 kHz of closed loop bandwidth, which is slow for a control loop and fine for a sensor. A transimpedance stage with a 1 megohm feedback resistor and 2 pF of photodiode capacitance has a pole near 80 kHz, so the amplifier bandwidth is not the limiting term there.

530 microamps per amplifier is the supply cost of the FET input, and it is why this family is described as low power rather than micropower. A four channel board running from plus or minus 15 V spends 32 mW in the quad before any signal, which is acceptable in a mains instrument and significant in a battery one.

18 nanovolts per root hertz at 100 Hz over a 10 kHz band is 1.8 microvolts RMS, which is larger than the 1 mV offset only in a wideband measurement. In a direct current application the offset and the bias current dominate and the noise figure is irrelevant, so the two specifications answer different questions.

The cascode input stage is what keeps the bias current flat as the common mode moves. A simple FET input has a bias current that climbs steeply as the input approaches the positive rail, and a board that measures at several common mode points sees a changing offset with a plain part and a constant one here.

2 volts per microsecond at 10 V peak to peak is about 32 kHz of full power bandwidth, well under the 1 MHz small signal figure. A circuit that needs 1 MHz of usable bandwidth at a volt or two of amplitude has to check the slew rate against the amplitude, not against the gain bandwidth product alone.

Where this order code fits

High impedance sensor front ends, photodiode transimpedance stages, pH and ion selective electrodes and electrometer style measurement use this part, because a 20 picoamp bias current into a 100 megohm source is 2 millivolts and a bipolar input would be volts. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Why not use a cheaper FET input amplifier? The 20 picoamp maximum and the 1 mV offset together are the selection. Many FET parts quote a typical bias current without a maximum over temperature, and a board that measures at 60 C needs the guaranteed number.

Can it drive a 10 nF load? Yes. The family is specified stable at unity gain with capacitive loads, which is the reason it appears behind long cables and sample and hold stages.

Does it invert phase when overdriven? No. Freedom from phase inversion on overdrive is stated in the family description, and it is one of the differences from older FET input parts.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.