Contact Us

MSP430F122IDW

Brand: Texas Instruments
Texas Instruments MSP430F122IDW is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MSP430F122IDW — Power Management & Signal Chain | Superb Automation

MSP430F122IDW

Texas Instruments — Power Management & Signal Chain

Product Overview

The MSP430F122IDW from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

MSP430F122IDW: 16 bit ultra low power microcontroller with 4 KB flash in a 28-pin wide body SOIC

MSP430F122IDW is a 16 bit RISC microcontroller with 4 KB of flash, a comparator, one USART and a 1.8 V to 3.6 V supply in a SOIC body of 28 pins. The MSP430F122 is the 4 KB member of the x12x family, and this DW code is the 28-pin wide body SOIC. It runs from 1.8 V to 3.6 V, draws 200 microamps in active mode at 1 MHz from 2.2 V, and wakes from standby in less than 6 microseconds. There is no analog to digital converter in this family: the analog block is a comparator with a programmable reference, so a board that needs a measurement channel has to add one or move to the F13x line.

Order code and package

Order codeMSP430F122IDW
Function16 bit RISC mixed signal microcontroller
PackageSOIC, 28 pins, wide body, code DW
Flash4 KB plus 256 bytes of information memory
RAM256 bytes
Supply range1.8 V to 3.6 V
Clockinternal DCO up to 8 MHz, external crystal or resonator
Timersone 16 bit Timer_A with three capture and compare registers
Serialone USART, selectable between UART and SPI
Analogcomparator_A with a programmable reference, no ADC
I/O22 pins across three ports
DatasheetSLAS312 revision C, July 2001 revised September 2004

Electrical parameters that decide the application

Active current200 microamps at 1 MHz from 2.2 V
Standby current0.7 microamps in low power mode 3
Off current0.1 microamps with RAM retained
Wake up timeless than 6 microseconds from standby
Instruction cycle125 nanoseconds at 8 MHz
Flash segments512 bytes per main memory segment, two 128 byte information segments
ProgrammingJTAG or bootstrap loader, no external programming voltage
Code protectionsecurity fuse
Low power modesfive, including off mode with RAM retention
Comparatorcomparator_A with an internal reference ladder

Points to check before this part goes on a BOM

The absence of an ADC is the fact most often missed when this code is quoted against the F13x family. The x12x devices offer comparator_A with a programmable reference, which measures a threshold and not a value, so a board that needs to read a thermistor or a shunt has to add an external converter or move to a device with ADC12.

Flash is organised as 512 byte main memory segments plus two 128 byte information segments. Code that writes calibration data has to place it in the information segments, because a main memory segment erase takes the whole 512 bytes with it, and the segment boundary is what determines whether a parameter update can happen without erasing the program.

200 microamps at 1 MHz is 200 microamps per megahertz, and the core can reach 8 MHz, so a full speed run is about 1.6 mA. At 1.8 V the same core runs slower and draws less, and the DCO wake in under 6 microseconds is what makes a duty cycled measurement cheaper than a continuous one.

The 28-pin DW body gives 22 I/O, and the port mapping is not symmetrical: port 1 and port 2 carry the timer and comparator functions while port 3 is general purpose. Interrupt capability sits on ports 1 and 2, so an input that has to wake the core belongs there and not on port 3.

The bootstrap loader means the part can be programmed through the USART after assembly, which is how a board without a JTAG header gets its firmware. The loader shares pins with port 1, so a board that uses those pins for something else cannot use the loader without a jumper or a bus contention arrangement.

Supply range down to 1.8 V is a real advantage for a two cell alkaline pack at end of life, but the flash write and erase require a higher minimum than the core does, so a firmware update at 1.9 V is outside the specified condition even though the core is still running.

Where this order code fits

Utility meters, sensor nodes, battery instruments and small motor controls that need a real 16 bit core and a comparator rather than a conversion channel use this code, and the 28-pin body keeps the board small enough for a potted enclosure. Boards comparing it with a neighbouring part start from our MCU Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does MSP430F122IDW have an ADC? No. It has comparator_A with a programmable reference. The 12 bit converter appears in the F13x family, and the F123 shares this limitation.

How much flash does this code carry? 4 KB of main flash plus 256 bytes of information memory, and 256 bytes of RAM. The F123 code in the same body carries 8 KB.

Can it run from a single lithium cell? A fresh cell at 3.6 V is inside the range and a discharged cell at 1.8 V is at the floor. Flash writes need more than that floor, so a firmware update on a nearly flat cell is not a supported condition.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.