Contact Us

LMKDB1204REXR

Brand: Texas Instruments
Texas Instruments LMKDB1204REXR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LMKDB1204REXR — Power Management & Signal Chain | Superb Automation

LMKDB1204REXR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LMKDB1204REXR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LMKDB1204REXR: two inputs, four outputs and PCIe Gen 7 additive jitter

The LMKDB1204REXR is the four output member of the LMKDB12xx clock mux group. Two reference inputs feed a low power HCSL mux, and four outputs fan the selected clock out to a PCIe link, a retimer, a switch or a set of endpoints. Additive jitter is 31 fs maximum root mean square over 12 kHz to 20 MHz at 156.25 MHz, and the vendor also publishes the per generation figures: 13 fs for Gen 4, 5 fs for Gen 5, 3 fs for Gen 6 and 2.1 fs for Gen 7.

Both common clock and independent reference architectures are supported, and the part accepts an input with or without spread spectrum clocking, so it can sit behind a source that spreads and a source that does not. Inputs are fail safe, which means an unpowered or floating input does not drag the bus. Loss of signal detection watches each input and disables the outputs automatically when the selected reference disappears, and that behaviour is what keeps a downstream endpoint from locking to noise.

The device runs from 1.8 V or 3.3 V at plus or minus 10 per cent and is specified over minus 40 C to plus 105 C. Output impedance is selectable between 85 ohm and 100 ohm, and each output has its own enable pin. A side band interface gives high speed enable and disable control, which is the route used when a hot plug event has to remove one endpoint clock without touching the rest of the tree.

Key data for the LMKDB1204REXR

FunctionTwo input clock mux with four LP HCSL outputs, common clock and independent reference both supported
Additive jitter31 fs maximum root mean square over 12 kHz to 20 MHz at 156.25 MHz, 13 fs Gen 4, 5 fs Gen 5, 3 fs Gen 6, 2.1 fs Gen 7
ComplianceDB2000QL, PCIe Gen 1 through Gen 7
InputsFail safe, with or without spread spectrum, loss of signal detection on each input
OutputsFour LP HCSL, individual enable, 85 ohm or 100 ohm output impedance selected by register
Supply1.8 V or 3.3 V at plus or minus 10 per cent
ControlSMBus register access plus a side band interface for fast output enable and disable
TemperatureMinus 40 C to plus 105 C ambient

Body, packing and marking data

BodyVQFN REX, 28 pins, 4 mm by 4 mm, which is the body the mechanical data lists for this string
Packing3000 pieces on a large reel on the lettered row, marking LMKDB
FinishNIPDAU, moisture level 1, 260 C peak, unlimited floor life
TemperatureMinus 40 C to plus 105 C on every published row of the group

Order code note before you place the string on a purchase order

There is a genuine table conflict on this string and it is worth knowing before an order is placed. The plain LMKDB1204REXR row in the addendum prints a 20 pin REY body, 250 pieces on a small reel and the marking DB1202, which belongs to the two output member. The lettered row immediately under it prints the 28 pin REX body at 3000 pieces on a large reel with the marking LMKDB, and the mechanical data at the back of the document lists LMKDB1204REXR as a 28 pin REX part.

Two of those three sources agree, and the odd one out is a row that looks like a column shift from the neighbouring device. The safe route is to state the body and the reel size on the purchase order in words rather than relying on the letter alone, and to check the marking on the first reel against the 28 pin REX expectation. A 250 piece small reel of the wrong device would pass a visual inspection and fail at the first configuration read over SMBus.

Where a four output mux earns its place

A server board rarely needs one reference clock. It needs the same 100 MHz reference at a root complex, at two endpoints and at a retimer, each on a different branch, and each with its own tolerance for jitter. One mux in front of four outputs removes three oscillators and the argument about which one goes where on the board.

The same reasoning applies in an accelerator card, where a hot plug event has to remove one clock without disturbing the others. Our OEM procurement page covers how these parts are kitted against a build schedule, and the date code management page is the one to read when a buffer with a register map has to be matched to a host revision at the assembly house.

Questions we get on this code

The first question is whether a mux can be used as a fanout buffer. It can, with one input selected and the selection left alone, but the part still carries the mux path and its loss of signal logic, so a board that only ever uses one reference pays for a feature it does not need. The buffer members of the same group are the cheaper answer in that case.

The second question is about the reference frequency. The jitter figures are quoted at 156.25 MHz, and a 100 MHz PCIe reference carries different numbers for the same silicon. Read the row that matches the frequency on the board, not the headline row at the top of the feature list.