LMK1C1104DQFR
Product Specifications
LMK1C1104DQFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LMK1C1104DQFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LMK1C1104DQFR: a 1 to 4 LVCMOS clock buffer in a 2 mm body
The LMK1C1104DQFR is a four output LVCMOS clock buffer that takes one clock input and fans it out four ways with less than 50 ps of output skew and less than 3 ns of propagation delay. It runs from 3.3 V, 2.5 V or 1.8 V, and the input is tolerant of 3.3 V levels at every supply voltage, so a 1.8 V buffer can accept a clock from a 3.3 V source without a level shifter in front of it.
The additive jitter is the number that matters for a fanout part, because a buffer that adds jitter defeats the purpose of a clean oscillator. This device adds 7.5 fs typical at 3.3 V, 10 fs at 2.5 V and 19.2 fs at 1.8 V, measured over the 12 kHz to 20 MHz band. That is low enough that the buffer can sit between a precision oscillator and four converters without changing the jitter budget in any meaningful way.
The maximum input frequency is 250 MHz at 3.3 V and 200 MHz at 2.5 V or 1.8 V. A synchronous output enable pin drives all four outputs low when it is asserted, and a fail safe input stops the outputs from oscillating when the input signal disappears, which prevents an unclocked converter from seeing a burst of noise instead of a defined state.
Key data for the LMK1C1104DQFR
| Function | 1 to 4 LVCMOS clock buffer with a synchronous output enable |
| Skew | Output to output skew below 50 ps |
| Additive jitter | 7.5 fs at 3.3 V, 10 fs at 2.5 V, 19.2 fs at 1.8 V typical over the 12 kHz to 20 MHz band |
| Delay | Propagation delay below 3 ns |
| Frequency | 250 MHz maximum at 3.3 V, 200 MHz at 2.5 V and at 1.8 V |
| Supply | 3.3 V, 2.5 V or 1.8 V, with a 3.3 V tolerant input at every rail |
| Inputs | Fail safe input that holds the outputs quiet when the clock disappears |
Body, packing and marking data
| Body | WSON DQF, 8 pins, the small leadless outline used on dense cards |
| Packing | 250 pieces on a small reel, the only packing printed for this string |
| Finish | NIPDAUAG, moisture level 1 with unlimited floor life, 260 C peak |
| Marking | L1C4 printed on the body |
| Temperature | Minus 40 C to plus 125 C |
A small reel is a production planning fact
This string ships 250 pieces on a small reel, not the 2500 that most clock buffers ship on. A prototype is well served by the small reel. A production run of ten thousand boards needs forty reels, and a line that stops every 250 pieces spends its day splicing. The same family offers other packing options on other strings, so the quantity has to be planned before the order code is fixed.
The benefit of the small reel is the short tail. A 250 piece reel that runs out at the end of a build leaves less scrap than a 2500 piece reel with 1800 pieces left on it, and a clock buffer with a limited shelf question is a part where the tail matters. Our component lead time solutions page covers how we plan a build around a packing size that does not match the line.
Where a 1 to 4 clock buffer is used
Four data converters on one card usually share one oscillator, and four traces from one oscillator pin will not hold skew. A buffer in the middle restores the drive and keeps the four clocks within 50 ps of each other, which is what a multi channel acquisition front end needs. The same part clocks four memory devices or four SerDes lanes.
When the board is moving from an older buffer of a different family, the pin map and the supply range are the two things to compare first. Our pin to pin cross reference page sets out that comparison, and the fail safe behaviour is worth checking in the same pass, because a buffer that oscillates on a missing clock will pass a bench test and fail in the field.
Questions we get on this code
Buyers ask whether the outputs can be used as separate enables. They cannot. The enable pin is common to all four outputs and it is synchronous, so all four stop together at the end of a clock period rather than in the middle. A board that needs independent gating needs a different device or a gate after the buffer.
The second question is whether the input can take a sine wave from an oscillator. It can, as long as the swing crosses the input threshold cleanly and the frequency stays inside the rated range. A sine wave with a slow edge will add jitter at the buffer, and the 7.5 fs figure assumes a square wave input with a fast edge.