Contact Us

LM293ADGKR

Brand: Texas Instruments
Texas Instruments LM293ADGKR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM293ADGKR — Power Management & Signal Chain | Superb Automation

LM293ADGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM293ADGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM293ADGKR: the dual comparator in the 3 millimetre VSSOP body

LM293ADGKR is the A grade of the dual comparator family in the eight pin VSSOP body, 3.00 by 3.00 millimetres, on tape and reel. Two comparators, a supply pin, a ground pin and four input and output pins in a body that is smaller than the SOIC-8 footprint's silk outline.

The A grade is the offset sort: 2 millivolts maximum at 25 degrees and 4 millivolts over the temperature window, against 5 and 9 on the base grade. The window is minus 25 to plus 85 degrees, which is the industrial band in the European sense and the band most equipment actually runs in.

The part is chosen for two reasons: two thresholds in a small body, and an input range that reaches ground on a single supply. Both are family traits rather than features of this string, and both are why the LM393 family is still on new bills of material after four decades.

Reading the code and the body

LM293 is the die and the temperature grade, A is the offset sort, DGK is the VSSOP body, and R is the reel. The body is 3.00 by 3.00 millimetres with a 0.65 millimetre pitch, which is the same pitch as the TSSOP but in a square outline. The reel carries 2500 pieces, and the moisture level is 1 at 260 degrees.

The pinout follows the dual comparator convention: outputs on pins 1 and 7, inverting inputs on 2 and 6, non-inverting inputs on 3 and 5, ground on 4 and supply on 8. Any board built for a SOIC-8 LM393 accepts this part with a footprint change and no electrical change.

Orderable codeLM293ADGKR
Comparators per body2
BodyVSSOP, 8 pins, 3.00 by 3.00 millimetres
Carriertape and reel, 2500 pieces
Offset at 25 degrees, A grade1 millivolt typical, 2 maximum
Offset over temperature, A grade4 millivolts maximum
Bias current25 nanoamps typical, 250 maximum
Common mode rangeground to 1.5 volts below the positive rail
Supply current, two comparators0.45 milliamps typical at 5 volts, 1 milliamp maximum
Output sink at 1.5 volts6 milliamps minimum
Saturation at 4 milliamps130 millivolts typical, 400 maximum
Response time1.3 microseconds typical
Temperature windowminus 25 to plus 85 degrees

The 250 nanoamp bias current and what it forbids

Two hundred and fifty nanoamps across a 1 megaohm source is a quarter of a volt. That is not a subtle error; it is a threshold that moves by a quarter of a volt depending on the source impedance. Any divider feeding this part has to stay below about 100 kiloohms in Thevenin terms if the offset grade is to mean anything.

Below that, the bias current is a small correction. At 10 kiloohms the worst case error is 2.5 millivolts, which is the same order as the A grade offset, and the two add. That is the point where an engineer stops paying for the A grade and starts paying for a lower bias part.

The input current also has a temperature coefficient. At 85 degrees it roughly doubles against its room temperature value, so a divider that is marginal at 25 degrees is worse at the top of the window. The offset current, at 50 nanoamps maximum, is the differential part of the same effect and is what a balanced divider cancels.

Single supply, split supply and the input range in between

The family runs from 2 volts to 36 volts single supply, and from a split supply with the same total. The input range includes the negative rail and stops 1.5 volts below the positive rail at 25 degrees, 2 volts over temperature. On a 5 volt single supply that is a usable window from 0 to 3.5 volts at room temperature and 0 to 3 volts hot.

On a split plus or minus 15 volt supply the same rule applies to each rail, and the comparator can sit in the middle of a signal that swings symmetrically. That is the configuration most audio and instrumentation boards use, and it is the reason the family survived the move to single supply logic.

One input may exceed the positive rail as long as the other stays in range. Both may go to the rail without damage. Neither may go more than 0.3 volts below the negative rail, which on a single supply means no negative excursion at all.

Output: open collector into whatever rail is available

The output is an open collector transistor with a 6 milliamp minimum sink at 1.5 volts and a saturation of 130 millivolts typical at 4 milliamps. The collector can be pulled up to 30 volts independently of the supply, which is how a 3.3 volt comparator drives a 12 volt relay or a 5 volt logic input from a 24 volt board.

The pull-up sets both the low level and the rise time. At 4 milliamps the guaranteed saturation is 400 millivolts, which is at the edge of a TTL low input. At 2 milliamps it is comfortably below. On a CMOS input the logic threshold is at half the rail and the saturation is irrelevant.

Leakage when the output is off is 0.1 nanoamps at room temperature and up to 1 microamp over temperature at 30 volts. On a 100 kiloohm pull-up that is 100 millivolts of error at the hot end, which is the number to check on a high impedance node.

Hysteresis and input filtering on a small body

A comparator with no hysteresis oscillates on any input that moves slowly through the threshold. The output changes, the input moves because of the change, and the part chases its own output until something else limits it. Positive feedback from the output to the non-inverting input fixes it and sets the width of the dead band.

On an open collector output the feedback resistor works against the pull-up, so the two are chosen together. A 100 millivolt dead band on a 5 volt rail with a 10 kiloohm pull-up needs roughly 200 ohms of feedback into a 10 kiloohm divider, and the exact value depends on the source impedance rather than on a formula that ignores it.

The input filter is the second half of the same problem. A 10 kiloohm series resistor and a 100 nanofarad capacitor give a 1 millisecond time constant, which is slow enough to swallow a contact bounce and fast enough to follow a mechanical event. A faster filter passes the noise the hysteresis was meant to reject.

Where the small dual body is the right answer

Two thresholds, a small board, a single supply and a mechanical scale event: a battery low indicator with a second level, a fan control with hysteresis, a door sensor with a debounce comparator, a zero crossing detector on a low voltage transformer.

It is the wrong answer for a precision window, for a signal faster than a microsecond, and for a board where the comparator has to survive a negative input excursion without a clamp.

Our amplifier cross reference page lists the dual equivalents and their offset grades, and the power management cross reference page covers the supply and reference parts that usually sit on the same rail.

Buying questions that come with this code

Does the DGK body need a different footprint from the SOIC-8? Yes, it is a 3 millimetre square VSSOP with a 0.65 millimetre pitch, so the land pattern is different even though the pinout is the same.

Is the A grade worth the premium? On a 10 millivolt threshold, yes. On a 500 millivolt threshold, no.

Can it run at 3.3 volts? Yes, and the input range still includes ground, with 1.8 volts of headroom to the positive rail.

Does the part need an external pull-up on the output? Yes. The output is an open collector and floats without one. The pull-up can sit on a rail above the supply, up to 30 volts, which is how a 3.3 volt comparator drives a 12 volt relay coil.