Contact Us

LM239AMDREP

Brand: Texas Instruments
Texas Instruments LM239AMDREP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM239AMDREP — Power Management & Signal Chain | Superb Automation

LM239AMDREP

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM239AMDREP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM239AMDREP: the enhanced product quad comparator on a full military window

LM239AMDREP is the enhanced product version of the quad differential comparator in the fourteen pin small outline body, on a 2500 piece reel, guaranteed from minus 55 to plus 125 degrees. The commercial LM239A stops at minus 25 to plus 85, so this string is the one that goes into a programme with an extended temperature requirement and a procurement file that has to stay open for a decade.

The letters carry more weight than the silicon. The enhanced product flow is built on one fabrication site and one assembly and test site, the baseline is held under configuration control, and the vendor commits to extended product change notification and to product traceability. For a buyer that is the whole point: the part is not faster or quieter than the commercial grade, it is the same circuit with a supply chain that will still answer a change notice in year eight.

What follows is what the string declares on the addendum, the electrical rows the wide window changes, the pin map of the fourteen pin body, and the cases where four comparators in one package beat four single devices.

What the enhanced product code declares

The document behind this code is SCLS496C, and it publishes three bodies from the same flow. The SOIC body comes as LM239AMDREP, the same body with a different tape route appears as LM239AQDREP, and the TSSOP body is LM239AMPWREP. The last one carries a narrower window than the SOIC parts, minus 40 to plus 125, which is a detail that catches people who assume every EP string is minus 55 to plus 125.

Orderable codeLM239AMDREP
Comparators per body4, independent
BodySOIC, 14 pins
Carrierlarge tape and reel, 2500 pieces
Temperature windowminus 55 to plus 125 degrees
Part markingLM239AME
Lead finishnickel palladium gold
Moisture ratinglevel 1, unlimited floor life at 260 degrees
RoHSyes
Supply voltage2 to 36 volts, split rails to plus or minus 18 volts
Differential input voltageplus or minus 36 volts
Output voltage rating36 volts, open collector
Output current rating20 milliamps
Related stringsLM239AQDREP, LM239AMPWREP, V62/03672-01XE

The fourth related string is worth a note. V62/03672-01XE is the standard military drawing number for the same die and the same body, printed on the same addendum page under the same minus 55 to plus 125 window. A programme that draws the SMD number and a programme that draws the EP number can end up buying the same parts, and only the paperwork differs. That matters at a last time buy, when the question is whether two strings can be merged into one order.

The rows the wide window changes

Offset voltage is 1 millivolt typical and 2.5 millivolts maximum at 25 degrees, and the maximum widens to 5.5 millivolts across the full minus 55 to plus 125 window. The commercial A grade holds 3 millivolts at room and 4 over its narrower window, so the EP part trades 0.5 millivolt of room temperature offset for 1.5 millivolts of headroom at the extremes. On a threshold that has to hold at 120 degrees this is the row that decides the divider, not the room temperature figure.

The bias rows move the same way. Input offset current is 5 nanoamps typical and 50 maximum at room, widening to 150 over the window. Input bias current is 25 nanoamps typical and 250 maximum, widening to 400. A 200 kilo ohm divider with 400 nanoamps of bias current sits 80 millivolts off, which is 15 times the offset window, so a wide temperature circuit that keeps a high impedance divider is limited by bias current drift and not by the offset grade.

Input offset voltage at 25 degrees1 millivolt typical, 2.5 maximum
Input offset voltage over the window5.5 millivolts maximum
Input offset current at 25 degrees5 nanoamps typical, 50 maximum
Input offset current over the window150 nanoamps maximum
Input bias current at 25 degrees25 nanoamps typical, 250 maximum
Input bias current over the window400 nanoamps maximum
Common mode range at 25 degreesground to 1.5 volts below the positive rail
Common mode range over the windowground to 2 volts below the positive rail
Large signal gain50 volts per millivolt minimum, 200 typical
Output low voltage at 4 milliamps150 millivolts typical, 400 maximum
Output low voltage over the window700 millivolts maximum
Output sink current at 1.5 volts6 milliamps minimum, 16 typical
Supply current, four comparators0.8 milliamps typical, 2 maximum
Response time with 5 millivolts of overdrive1.3 microseconds typical

Four comparators on fourteen pins

The pin map is the reason the part survived. Output one and output two sit at pins one and two, the positive rail is pin three, and the ground is pin twelve, so a board that wants the four outputs on one side of the package can route them without crossing the inputs. Comparator one uses pins six and seven for its inputs, comparator two uses pins four and five, comparator three uses pins eight and nine, and comparator four uses pins ten and eleven.

Pin 1output of comparator 1
Pin 2output of comparator 2
Pin 3positive supply
Pin 4inverting input of comparator 2
Pin 5non inverting input of comparator 2
Pin 6inverting input of comparator 1
Pin 7non inverting input of comparator 1
Pin 8non inverting input of comparator 3
Pin 9inverting input of comparator 3
Pin 10inverting input of comparator 4
Pin 11non inverting input of comparator 4
Pin 12ground or negative supply
Pin 13output of comparator 4
Pin 14output of comparator 3

Four comparators in one body save three placements, three sets of decoupling and three part numbers on the line. They also put four heat sources in one package, which is the trade a wide temperature build has to look at. At 0.8 milliamps for the whole body the self heating is small, but the offset of a comparator that sits next to a hot regulator will follow the local board temperature and not the ambient the test report quotes.

The output and the wired AND

Each output is an open collector transistor rated to 36 volts and 20 milliamps, with a saturation voltage of 150 millivolts typical at 4 milliamps and 400 maximum, rising to 700 over the window. Because the collectors are free, several outputs can be tied to one pull up and the node goes high only when every comparator has released it. That is a wired AND, and it is how a four channel fault line becomes one signal without a gate.

Pull up sizing decides the rise time and the dissipation. With 5 volts and 4.7 kilo ohms the sink current is about 1 milliamp and the low level stays near 100 millivolts; with 1 kilo ohm the current is 5 milliamps and the low level approaches the 400 millivolt maximum. Leakage when the output is off is 50 nanoamps at room and 1 microamp over the window, so a 100 kilo ohm pull up can sit 100 millivolts above ground at 125 degrees, which is a real offset on the next stage.

Why one fabrication site matters for a long build

A comparator in a control loop is a low value line item and a high cost failure. The enhanced product flow answers the second half of that sentence: one fab, one assembly site, a controlled baseline, and a change notification route that reaches the customer before the parts do. Programmes that need a form fit function statement every two years find that the paperwork is the product.

Two of our pages go with this one. The component traceability report page sets out what we record per reel, lot and date code when a part has to be traceable to a fab, and the last time buy and LTB planning page covers the arithmetic of a bridge buy for a programme that runs past the vendor's notice date. Both were written for exactly this kind of string, where the schedule is longer than the catalogue.

Stocking is the other half. An EP part is usually bought once or twice a year in a single lot, because the price break sits at the reel and the reel is 2500 pieces. A build that consumes 300 a year is holding eight years of parts after one order, and the shelf life question then belongs to the moisture bag and not to the silicon, since the level 1 rating means no bake is required at any point.

Questions that come with this code

Is the EP part a different die from the commercial LM239A? The addendum publishes the same electrical table shape and the same pinout, and the enhanced product flow is a supply chain and qualification statement rather than a new circuit. The measurable difference on the page is the temperature window and the tighter offset maximum.

Can the TSSOP string be substituted? Only with a footprint change and only if minus 40 to plus 125 is enough, because LM239AMPWREP is published under that window rather than the military one.

What happens if the programme needs the SMD number instead? V62/03672-01XE is printed on the same page under the same window, so the two strings are interchangeable in the application and the choice is a contract question.