ISO7762FQDBQRQ1
Product Specifications
ISO7762FQDBQRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7762FQDBQRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7762FQDBQRQ1: Automotive six-channel digital isolator, four forward and two reverse, default low
ISO7762FQDBQRQ1 is an automotive qualified digital isolator with four channels in one direction and two in the other, for bidirectional links across a barrier in a SSOP (DBQ) body of 16 pins. It isolates 100 Mbps across a reinforced barrier with four channels forward and two reverse, is qualified for automotive use, and drives its outputs low when the input supply is lost.
Order code and package
| Ordering string | ISO7762FQDBQRQ1, DBQ package, 16-pin SSOP, automotive qualified, tape and reel |
| Channel arrangement | Four forward and two reverse, which is the 7762 member of the family |
| Qualification | Automotive Q1 grade, with the AEC-Q100 temperature range for the body |
| Package | 16-pin SSOP, 3000 VRMS barrier |
| Default state | Low on power loss, the F suffix |
| Safety | Reinforced insulation per VDE 0884-17, plus UL, CSA, CQC and TUV |
Electrical parameters that decide the application
| Data rate | 100 Mbps |
| Supply range | 2.25 V to 5.5 V on each side, with level translation |
| Propagation delay | 11 ns typical at 5 V |
| Common mode transient immunity | 100 kV per microsecond typical |
| Surge capability | Up to 12.8 kV |
| Power | 1.4 mA per channel typical at 1 Mbps |
| Temperature | -55 C to 125 C for the family, with the Q1 grade covering the automotive band |
| Lifetime | Over 30 years projected barrier life |
Points to check before this part goes on a BOM
The two reverse channels are the reason to pick this member over the six forward one. An SPI bus with a master and one slave needs four lines one way and one the other, and a fault line back makes six, which is exactly the 4 plus 2 split. Using a 6 forward part and a second isolator for the return path costs a package and a set of decoupling capacitors.
Automotive qualification changes the documentation, not only the silicon. The Q1 grade brings a production part approval process, a temperature qualification over the automotive band and a change notification commitment, and a purchasing decision that treats a Q1 part as interchangeable with the industrial one because the electrical table matches will fail an audit rather than a bench test.
The default low behaviour carries more weight in a vehicle than in a cabinet. A barrier whose control side loses power in a 12 V system during a cranking event must not command a gate driver on, so the F suffix is the safe choice wherever the isolated side drives a power stage. The non F part is for signals whose safe state is high, and mixing them on one board is a review item.
The 100 Mbps rate is far above what most automotive serial links need, and the reason to use it is the delay and the skew rather than the rate. A 10 MHz SPI clock has a 100 ns period and is comfortable, and a gate driver command path with 11 ns of delay leaves the dead time budget almost untouched. At 100 Mbps continuous the supply current becomes the limit, so the application rarely runs at the rated rate.
The SSOP body at 3000 VRMS is the practical choice for a control board inside an enclosure where the barrier is between a 12 V domain and a 48 V or high voltage domain with reinforced requirements of a few hundred volts. Where the barrier has to hold mains potential the wide body part is needed, and the board outline has to be planned for it before the board outline is frozen.
The 12.8 kV surge capability is a system level number only with the recommended external components. A surge arriving on the field side sees the isolation barrier in series with the board's own creepage, and a slot cut in the board under the part defeats the rating even when the correct part is fitted. The mechanical drawing in the data sheet is part of the electrical specification for this reason.
The two reverse channels draw their current from the opposite side, so the supply budget is not simply six times the per channel figure. In a four forward and two reverse arrangement the majority of the current sits on the control side, and the field side supply only has to carry two channels. With an isolated DC to DC converter of a few hundred milliwatts that difference is what decides whether the field side needs its own regulator, and the same arithmetic applies to the decoupling on each side. The per channel current also rises with the toggle rate, so a link that runs at 25 Mbps and a link that idles at 1 Mbps can differ by more than ten times in supply current, and the isolated converter has to be sized for the fastest state the product ever uses.
Where this order code fits
It is used in automotive and industrial control units that need a bidirectional link across an isolation barrier, such as an SPI connection to a gate driver with a fault return, a battery management front end, or a sensor interface in a traction inverter. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Defense Grade Components page.
Questions buyers ask
Is it a drop-in for the industrial version? Electrically it matches the industrial part in the same package, but the Q1 qualification, the documentation and the change control are different, so it is not interchangeable in a qualified product.
How are the six channels arranged? Four in the forward direction and two in the reverse, which suits a four-wire bus with two return signals.
Does it need a separate isolated supply on each side? Yes. The barrier isolates signals, not power, so each side needs its own supply, typically an isolated DC to DC converter or a transformer driver.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Medical Device Components page sets out the checks that keep a substitute from failing on the bench.