ISO7760FDBQR
Product Specifications
ISO7760FDBQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7760FDBQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7760FDBQR: Six-channel reinforced digital isolator, 100 Mbps, default low output
ISO7760FDBQR is a six-channel digital isolator that passes 100 Mbps across a reinforced barrier with a defined low output when power is lost in a SSOP (DBQ) body of 16 pins. It isolates six logic channels at 100 Mbps with 11 ns of typical propagation delay, draws 1.4 mA per channel at 1 Mbps, and holds its outputs low when the input side loses power, which is the F suffix.
Order code and package
| Ordering string | ISO7760FDBQR, DBQ package, 16-pin SSOP, tape and reel |
| Family members | ISO7760 to ISO7763 in six, five, four and three forward channels; F suffix for default low |
| Package | 16-pin SSOP, 3000 VRMS rating, versus 5000 VRMS in the wide body SOIC |
| Ambient range | -55 C to 125 C |
| Channels | Six, all in the same direction on the ISO7760 |
| Safety | Reinforced insulation per VDE 0884-17, UL 1577, CSA, CQC and TUV |
Electrical parameters that decide the application
| Data rate | 100 Mbps |
| Supply range | 2.25 V to 5.5 V on both sides, with level translation between them |
| Propagation delay | 11 ns typical at 5 V |
| Power | 1.4 mA per channel typical at 1 Mbps |
| Common mode transient immunity | 100 kV per microsecond typical |
| Surge | Up to 12.8 kV |
| Default state | Low on power loss for the F suffix, high without it |
| Lifetime | Over 30 years projected isolation barrier life |
Points to check before this part goes on a BOM
The F suffix is a safety decision. Without it the outputs default high when the input side loses power, and a gate driver or a relay enable that reads high will turn on. With it the outputs default low, so a lost supply on the control side commands the field side to the off state. A bill of materials that substitutes the non F part in a safety path has changed the behaviour of the product without changing a single wire.
The DBQ body is rated 3000 VRMS while the DW body is rated 5000 VRMS. Same silicon, different package and different creepage, and the choice is dictated by the clearance the product's insulation coordination needs, not by the data rate. A board specified for 5 kV that is built with the SSOP body has a certificate problem even if it works perfectly.
At 100 Mbps the 11 ns delay is what makes the part usable as a digital isolator rather than as a slow coupler. A 100 Mbps clock has a 10 ns period, so a delay of 11 ns is about one bit, and the channel to channel skew and the pulse width distortion become the numbers that decide whether a parallel bus survives the barrier. For SPI above 25 MHz the part still works, and the loop delay has to be included in the timing budget.
The 1.4 mA per channel at 1 Mbps is the figure to use for a standby calculation, and it scales with the toggle rate. Six channels at 1 Mbps is 8.4 mA total, at 25 Mbps it is over 200 mA, which in a 16-pin body is a thermal question as well as a supply question. A quiet bus that idles high draws far less than the headline figure, so the current in a real system is between the two.
Level translation is free inside the part, and that is worth planning for. A 3.3 V processor on one side and a 5 V field interface on the other needs no external shifter, and the part is specified to translate between any two supplies inside 2.25 V to 5.5 V. The one combination to avoid is a 1.8 V side, which is below the minimum, and a 1.8 V processor needs a different family.
The barrier is capacitive with silicon dioxide, and the 30 year lifetime figure assumes the working voltage stays inside the specification. In a 690 V drive the working voltage across the barrier is not the bus voltage but the potential difference between the two grounds, which in a fault can be the full DC link. Sizing the barrier for the nominal voltage and not the fault voltage is the most common isolation mistake in industrial equipment.
Each side of the barrier needs its own decoupling and its own supply, and the two grounds must not be joined anywhere on the board. A 0.1 microfarad capacitor within a few millimetres of each supply pin is the usual requirement, and the isolated side supply has to come from a converter or a transformer driver rated for the working voltage of the barrier. The most common failure in a first build is a ground stitch that bridges the barrier under the part, which leaves the channels working and the isolation gone.
Where this order code fits
It is used to isolate SPI, UART and GPIO between a control board and a power stage in motor control, industrial automation, solar inverters, power supplies and medical equipment, and it is the default choice where six channels have to cross one barrier in the same direction. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
What does the F suffix change? Only the default output state on power loss. The F parts drive the output low, the parts without F drive it high, and the data rate, current and timing are identical.
Can it isolate a 1.8 V processor? No. The minimum supply is 2.25 V, so a 1.8 V logic side needs a part from a family with a lower minimum.
Is the 3000 VRMS rating enough for mains equipment? It depends on the insulation coordination the product needs. The SSOP body is 3000 VRMS and the wide SOIC body of the same part is 5000 VRMS, so the package decides the rating.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Defense Grade Components page sets out the checks that keep a substitute from failing on the bench.