Contact Us

ISO7741FDWR

Brand: Texas Instruments
Texas Instruments ISO7741FDWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7741FDWR — Power Management & Signal Chain | Superb Automation

ISO7741FDWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7741FDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7741FDWR: quad channel digital isolator with three forward and one reverse

ISO7741FDWR is a quad channel reinforced digital isolator in a SOIC body of 16 pins. It carries four digital signals across a 5000 V RMS barrier, three in the forward direction and one back, at up to 100 Mbps per channel. The FDWR order code is the wide body 16-pin SOIC with the default low option on a 2000 piece reel.

Order code and package

Order codeISO7741FDWR
Package16-pin wide body SOIC, DW, 5000 V RMS
Packingtape and reel, 2000 pieces
Channelsfour, three forward and one reverse
Signalling rate100 Mbps
Isolation5000 V RMS, reinforced
Default stateoutput low, F suffix
Supply2.25 V to 5.5 V on each side

Electrical parameters that decide the application

Propagation delay10.7 ns typical at 5 V
Supply current1.5 mA per channel at 1 Mbps
Common mode transient immunity100 kV per microsecond typical
Surge capabilityup to 12.8 kV
Working voltage lifeover 30 years projected at 1500 V RMS
Temperature rangeminus 55 to plus 125 degrees

Family variants and how they differ

ISO7740four channels all forward
ISO7741three forward and one reverse, this order code
ISO7742two forward and two reverse
ISO7740FDWRfour channels all forward in the same package

Points to check before this part goes on a BOM

Three forward and one reverse is the arrangement of a three phase bridge: three gate commands out and one fault or ready line back. It is also the arrangement of a serial peripheral interface with a chip select and a clock out and data in, which is why this channel count outsells the symmetric quad versions in motor control.

The 5000 V RMS rating here is the wide body package, and the reinforced classification is what allows the part to be used where a basic insulation part is not enough. The DWV eight pin package carries the same silicon at 5000 V RMS, and the narrow D package falls to 3000 V RMS.

Ten point seven nanoseconds of delay per channel with four channels means the three forward signals arrive together within the channel to channel skew. A bridge driver that relies on three gate signals switching at the same instant has to budget that skew in its dead time, and the skew figure is separate from the delay figure in the data sheet.

The one reverse channel is usually a fault or a desaturation flag rather than data. Its default state on loss of input power is low with the F suffix, which means a fault line reads as clear when the isolated side has lost power. Firmware that treats the fault line as an active low signal needs an inverting stage or the non F part.

Supply current of 1.5 mA per channel at 1 Mbps is a per channel figure, so four channels cost 6 mA before the switching component. That is the sum the isolated rail has to supply, and it is the number that decides whether a small transformer driver can power the barrier.

Common mode transient immunity of 100 kV per microsecond typical is what makes the part usable next to a switching bridge. The typical figure has no minimum in the summary line, so a product that sees faster edges than the typical case has to look at the full table rather than the headline.

Both supply pins are 2.25 V to 5.5 V, so the part translates between a 3.3 V controller and a 5 V isolated side without extra components. The two supplies must be independent, and the wide body package gives the creepage distance that a 5 kV barrier requires on the board.

Three forward channels that switch together are the case where channel to channel skew matters. A bridge leg that turns on one switch before the other has cross conduction for the duration of the skew, and the skew figure in the data sheet is measured at one temperature and one supply, so the dead time has to cover the worst case over both.

The isolated rail has to supply four channels at their switching current plus the load on the far side. At 1 Mbps that is 6 mA, and a burst at 100 Mbps multiplies it. A transformer driver sized for the idle current will drop the rail during a burst, and the resulting undervoltage reset looks like a protocol error rather than a power problem.

Four channels on one barrier share a single pair of supply pins, so the current a module draws is the sum even when only one channel is switching. a board that budgets the isolated rail from the current of the active channel and then runs all four at speed finds the rail sagging, and the symptom is usually a channel that stops responding rather than a supply that measures low.

Where this order code fits

It is used for three phase bridge gate signals with fault readback, isolated serial peripheral interfaces, industrial input output modules and medical equipment that needs four signals across one reinforced barrier. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.

Questions buyers ask

How many channels run each way? Three forward and one reverse. The ISO7742 has two and two, and the ISO7740 has all four forward.

What package gives 5000 V RMS? The wide body 16-pin DW and the eight pin DWV. The narrow eight pin D package is 3000 V RMS.

Does the F suffix matter for the reverse channel? Yes. It sets that channel low when the input side loses power, which reverses the meaning of a fault line for the controller.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.