ISO7740FDBQR
Product Specifications
ISO7740FDBQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7740FDBQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7740FDBQR: four forward channels at 100 Mbps
The ISO7740FDBQR is the four channel member of the ISO774x family with every channel forward and a low default. It is the part a board reaches for when four signals have to cross a barrier at speed and none of them needs to come back: a parallel data bus, four chip selects, four gate commands or a quad clock and data set. The 100 Mbps rating covers a fast serial link as easily as it covers a slow control line.
The F letter sets the state on loss of input power or input signal to low. That is the safe state for a gate command or an active high enable, and it removes the need for external pull downs on the isolated side. The plain version of the same die holds the outputs high through the same event, which suits an active low release signal.
Isolation in this shrink body is 3000 VRMS for one minute under UL 1577 and 4242 VPK under the VDE certificate, with the wide body of the same family carrying 5000 VRMS and 8000 VPK. Propagation delay is 6 ns minimum, 12.7 ns typical and 17 ns maximum at 5 V, and the supply current is 1.5 mA per channel typical at 1 Mbps.
Key data for the ISO7740FDBQR
| Channels | Four, all forward, with an output enable pin for multi driver buses |
| Data rate | 100 Mbps maximum specified |
| Isolation in this body | SSOP DBQ gives 3000 VRMS and 4242 VPK, the wide SOIC body of the same family gives 5000 VRMS and 8000 VPK |
| Supply | 2.25 V to 5.5 V on each side, 2.25 V to 5.5 V level translation |
| Timing | Propagation delay 12.7 ns typical and 17 ns maximum at 5 V, pulse width distortion 5.9 ns on same direction channels |
| Immunity | CMTI 100 kV per microsecond typical and 85 kV per microsecond minimum |
| Default state | Output low on loss of input power or signal, the F variant |
Body, packing and marking data
| Body | SSOP DBQ, 16 pins, 4.9 mm by 4.9 mm |
| Packing | 2500 pieces on a large reel on the plain, the A row and the G4 row |
| Finish | NIPDAU, moisture level 2, 260 C peak, one year floor life |
| Marking | 7740F on the body, without the reel size or the qualification status |
| Temperature | Minus 55 C to plus 125 C |
Choosing the body before choosing the part
The same die is released in two bodies with two isolation ratings, and the order string only tells you which one by its suffix. A DBQ string is the 4.9 mm shrink body at 3000 VRMS. A DW string with the same channel map is the wide body at 5000 VRMS. Buying by channel count alone gets the right function and possibly the wrong certificate.
For a mains referenced product, the wide body is usually the simpler answer because the creepage comes with the package. For a dense card behind a low voltage barrier, the shrink body saves 5 mm of board per isolator, and that difference decides whether the card fits the enclosure. Both are valid, and the safety file has to name the one that is on the board.
Where four fast forward channels are used
Motor control uses four channels for three high side gate commands and one enable, or for a quadrature encoder pair plus two index lines. Instrument front ends use the same count for a four wire serial bus. The 100 Mbps rate is what allows a fast isolated link without a serializer, which removes a component and a protocol from the board.
Medical monitors put the barrier between patient connected circuitry and the mains referenced side, and our medical device component sourcing page lists the certificates a reviewer asks for. When the board is moving from a four channel part of another family, the pin to pin cross reference page is where the comparison starts.
Questions we get on this code
Buyers ask whether the F suffix can be dropped when stock is short. It cannot, because the default state is a functional property, not a packing option. A board that expects a low output on loss of field power and receives a high output instead will hold a gate on, which is the fault the default was chosen to prevent.
The second question is about the enable pin. It sets the outputs to high impedance and leaves the barrier switching. Two controllers can therefore share one set of isolated lines as long as the switchover logic drives both enables, and the gap during the changeover is longer than one bit at 100 Mbps, so the protocol has to tolerate it.
A third question comes up on new project quotes: whether one six channel part could replace two four channel parts. It can when the channel count fits, but the answer changes the board, the reel size and the safety certificate at once. We quote the six channel option and the two part option side by side with the reel quantity for each, because the cheaper unit price is not always the cheaper board.