Contact Us

ISO7721FDR

Brand: Texas Instruments
Texas Instruments ISO7721FDR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7721FDR — Power Management & Signal Chain | Superb Automation

ISO7721FDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7721FDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7721FDR: dual channel digital isolator with one channel in each direction at 100 Mbps

ISO7721FDR is a high speed dual channel digital isolator in a SOIC body of 8 pins. It carries two digital signals in opposite directions at up to 100 Mbps, which is the arrangement a command and a reply need across one barrier. The F suffix sets the outputs low when the input side loses power, and the DR order code is the eight pin SOIC on a 2500 piece reel at a 3000 V RMS rating.

Order code and package

Order codeISO7721FDR
Package8-pin SOIC, D, rated 3000 V RMS
Packingtape and reel, 2500 pieces
Channelstwo, one forward and one reverse
Signalling rate100 Mbps
Isolation3000 V RMS in this package, 5000 V RMS in DW and DWV
Default stateoutput low on loss of input power, F suffix
Supply2.25 V to 5.5 V on each side

Electrical parameters that decide the application

Propagation delay11 ns typical at 5 V
Supply current1.7 mA per channel at 1 Mbps
Common mode transient immunity100 kV per microsecond typical
Surge capabilityup to 12.8 kV
Working voltage lifeover 30 years projected at 1500 V RMS
Temperature rangeminus 55 to plus 125 degrees

Family variants and how they differ

ISO7720two channels both forward
ISO7721two channels, one each direction, this order code
ISO7741four channels, three forward and one reverse
ISO7721FDWwide body package rated 5000 V RMS

Points to check before this part goes on a BOM

The isolation rating depends on the package and not on the family name. This order code is the narrow eight pin body at 3000 V RMS, while the same silicon in the wide body packages reaches 5000 V RMS. A specification that quotes 5000 V RMS and orders this code is one package away from being wrong.

One channel each way is the useful arrangement for an isolated serial link, a gate driver with status readback, or a converter with a telemetry line. The ISO7720 has both channels in the same direction, and the two parts are not interchangeable on a board even though the pinout is the same eight pins.

The F suffix sets the default output low when the input side loses power or the signal stops toggling. Without the F the output goes high, which on a driver enable line means the bridge turns on during a supply loss. The suffix belongs in the order code, not in a note on the assembly drawing.

Delay of 11 ns typical at 5 V is short enough that the barrier no longer dominates the timing of a control loop. At 100 Mbps a bit is 10 ns, so the delay is about one bit time, and the part is specified for the rate the delay allows rather than the other way round.

Supply current of 1.7 mA per channel at 1 Mbps is the figure to size the isolated rail from. At 100 Mbps the same channel draws several times that, so a link that runs fast in bursts needs the rail sized on the burst rather than on the average.

The 2.25 V to 5.5 V range covers a 2.5 V controller on one side and a 5 V field device on the other. Both sides need independent supplies for the barrier to function, and a shared ground between the two sides turns the part into an expensive level translator.

Temperature range extends to minus 55 degrees, which is below the usual industrial minus 40. That matters for outdoor equipment in cold climates, and it is one of the few specifications where this family is wider than an optocoupler replacement.

A bidirectional link needs the reverse channel to survive the same common mode transient as the forward one, and that is the channel that usually carries the fault flag. A part with one reverse channel is therefore enough for a command and a status pair, and a second reverse channel is only needed when the protocol carries two independent replies.

Propagation delay matters in both directions on a bidirectional link because the round trip sets how quickly a controller can react. Eleven nanoseconds each way plus the cable and the driver is still short of a microsecond, so the barrier is not the limit for any loop that samples faster than 100 kHz.

A reverse channel on a bidirectional link carries the reply, and the reply is usually the signal that reports a fault. Its default state therefore decides what the controller believes when the isolated side is unpowered, and a default low fault line on an active low input reads as a permanent fault, while on an active high input it reads as clear. The suffix and the polarity of the receiving input have to be chosen together.

Where this order code fits

It is used for isolated serial links, gate drive interfaces with status readback, isolated analog front ends, motor control boards and instrumentation that needs two signals across one barrier. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Is this the 5000 V RMS part? No. This is the eight pin D package at 3000 V RMS. The wide body packages reach 5000 V RMS under different order codes.

What does the F suffix do? It makes the outputs default low when the input side has no power, which is the safe state for an enable or a reset line.

Can the channels be used in the same direction? Not on this code. The ISO7720 has both forward, and using the wrong one reverses a channel with no other change visible.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.