ISO7720FQDRQ1
Product Specifications
ISO7720FQDRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7720FQDRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7720FQDRQ1: automotive dual channel digital isolator with both channels forward
ISO7720FQDRQ1 is an automotive grade dual channel digital isolator in a SOIC body of 8 pins. It carries two digital channels in the same direction at up to 100 Mbps across a 3000 V RMS barrier in the eight pin body, with the F suffix setting the output low on loss of input power. The QDRQ1 order code is the automotive grade eight pin SOIC on a 2500 piece reel.
Order code and package
| Order code | ISO7720FQDRQ1 |
| Package | 8-pin SOIC, D, 3000 V RMS rating |
| Packing | tape and reel, 2500 pieces |
| Qualification | AEC-Q100 grade 1, minus 40 to plus 125 degrees |
| Channels | two, both in the same direction |
| Signalling rate | 100 Mbps |
| Default state | output low, F suffix |
| Supply | 2.25 V to 5.5 V on each side |
Electrical parameters that decide the application
| Isolation rating | 3000 V RMS in the D package, 5000 V RMS in DW and DWV |
| Surge capability | up to 12.8 kV |
| Common mode transient immunity | 100 kV per microsecond typical |
| Supply current | 1.7 mA per channel at 1 Mbps |
| Propagation delay | 11 ns typical |
| Temperature range | minus 40 to plus 125 degrees |
| Isolation lifetime | over 30 years projected at 1500 V RMS working |
Family variants and how they differ
| ISO7720-Q1 | two channels both forward, this order code |
| ISO7721-Q1 | two channels, one each direction |
| ISO7740-Q1 | four channels all forward |
| ISO7720FQDWQ1 | wide body package rated 5000 V RMS |
Points to check before this part goes on a BOM
The headline 5000 V RMS rating in the family features belongs to the wide body packages. This order code is the eight pin D package, which is rated 3000 V RMS, and a customer who reads the first bullet of the data sheet and not the package table will overstate the barrier by 2000 V.
Both channels run in the same direction on the ISO7720, which suits two control lines crossing one barrier or a clock and a data line. The ISO7721 in the same family has them in opposite directions, and swapping the two order codes reverses one channel without any other change.
The F suffix sets the output low when the input side loses power or signal. With two channels both forward, that means both outputs fall low together, which is the state a bridge enable pair or a pair of gate signals needs in a fault.
Automotive grade 1 covers minus 40 to plus 125 degrees ambient, and the isolation lifetime figure of 30 years is projected at 1500 V RMS working voltage. Running the part at its 3000 V RMS withstand level continuously is not what the lifetime projection covers, and a traction system has to state its working voltage rather than its test voltage.
The 2.25 V to 5.5 V supply range on both sides allows a 2.5 V or 3.3 V controller to talk to a 5 V field device without translation. Both sides still need independent supplies, and on a vehicle harness the field side supply is usually an isolated rail from a transformer driver.
Common mode transient immunity of 100 kV per microsecond typical is the figure for the family, and it is a typical rather than a minimum. In a motor inverter the difference between typical and minimum is the difference between a link that survives production units and one that survives only the bench.
Propagation delay of 11 ns typical with two matched channels allows the pair to carry a clock and a data line with a known skew. A driver stage that relies on the two arriving together has to budget the channel to channel skew and not only the delay.
Automotive qualification brings a production part approval process with it, and the order code has to carry the Q1 suffix for the paperwork to match. A build that uses the industrial part because it is available and then submits a PPAP against the automotive code has a documentation problem before it has a technical one.
The two channels share one barrier and one pair of supplies, so a fault on one side affects both. On a bridge enable pair that is the intended behaviour, and on a link carrying two independent signals it is not, which is why the channel arrangement is chosen with the failure mode in mind rather than the pin count.
Two channels in the same direction on one barrier are often a clock and a latch, or a pair of gate commands for one leg of a bridge. In both cases the two signals have to arrive with a known relationship, and the channel to channel skew of the isolator is part of that budget. A pair that is specified to switch together but arrives a few nanoseconds apart turns into cross conduction in the switch pair it drives.
Where this order code fits
It is used in automotive motor drives, battery management, on board chargers, dc to dc converters and isolated sensor interfaces that need two control lines across one barrier. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Is this part 5000 V RMS? No. This order code is the eight pin D package rated 3000 V RMS. The 5000 V RMS figure applies to the DW and DWV wide body packages.
What does F change? It sets the default output to low when the input side loses power. Without the F, both outputs go high in that state.
Can the two channels run in opposite directions? Not on this order code. Both channels are forward, and the ISO7721Q is the opposite direction variant.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.