ISO7421FEDR
Product Specifications
ISO7421FEDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7421FEDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7421FEDR: dual channel digital isolator in opposite directions at 1 Mbps
ISO7421FEDR is a low power dual channel digital isolator in a SOIC body of 8 pins. It provides two isolated channels, one in each direction, for a bidirectional link at up to 1 Mbps across a 2500 V RMS barrier, in a narrow body eight pin package. The suffix on this order code does not appear in the vendor orderable addendum, which lists the ISO7421D and ISO7421DR only, so the exact code has to be confirmed against a purchase order.
Order code and package
| Order code on the page | ISO7421FEDR, suffix to be confirmed with the vendor addendum |
| Addendum listing | ISO7421D in tubes and ISO7421DR on a 2500 piece reel |
| Package | 8-pin narrow body SOIC, D |
| Channels | two, one forward and one reverse |
| Signalling rate | 1 Mbps maximum |
| Isolation | 2500 V RMS for one minute per UL |
| Supply | 3.3 V or 5 V on each side, level translation between them |
Electrical parameters that decide the application
| Supply current | 1.5 mA per channel at 3.3 V typical |
| Propagation delay | 9 ns typical |
| Channel to channel skew | 300 ps typical |
| Transient immunity | 50 kV per microsecond typical |
| Temperature range | minus 40 to plus 125 degrees on the M grade |
| Isolation lifetime | over 25 years at rated voltage |
Family variants and how they differ
| ISO7420 | two channels, both forward |
| ISO7420M | two channels forward, extended temperature |
| ISO7421 | two channels, one each direction |
| ISO7421DR | the orderable code listed in the vendor addendum |
Points to check before this part goes on a BOM
The order code on this page is the first thing to check. The vendor addendum for the family lists ISO7420D, ISO7420DR, ISO7421D and ISO7421DR, and the FE suffix in ISO7421FEDR does not appear there. A quotation against this string without the addendum open risks shipping a part that does not exist under that name, so the code should be confirmed before a purchase order is placed.
The channel arrangement is one forward and one reverse, which is what a bidirectional link needs: a command out and a status back across the same barrier. The ISO7420 in the same family has both channels in the same direction and is a different order code for a different application.
A 1 Mbps ceiling is low against the 25 Mbps and 100 Mbps members of the same product line, and that is deliberate: the ISO742x family is built for low power and long isolation life rather than for speed. A link that needs more than 1 Mbps has to move to another family, not to another order code in this one.
Supply current of 1.5 mA per channel at 3.3 V is the reason the family still exists. On a loop powered instrument that budget is the difference between a two wire transmitter and a four wire one, and the same link built with a faster isolator draws several times that figure.
The part needs two supply voltages and translates between them, so a 3.3 V controller and a 5 V field side are supported. The two rails have to be independent for the barrier to mean anything, and a shared ground on both sides is the most common wiring error in a prototype.
Transient immunity of 50 kV per microsecond typical is quoted without a minimum in the summary line. For a link next to a contactor or a motor cable, the missing minimum is what should decide whether this family or the higher immunity ISO772x family is used.
Because this order code does not appear in the addendum, a quotation has to be built from a confirmed code. The practical route is to ask the customer for the marking on the part they already use, or to quote ISO7421DR and state the substitution in writing, rather than to ship a reel whose label does not exist in the vendor's own list.
The family is chosen for its supply current, so the surrounding circuit has to respect that. A loop powered instrument that budgets 1.5 mA per channel has no room for a pull up resistor that draws more than the isolator, and an open drain output with a 10 k pull up on a 3.3 V rail already draws 330 microampere.
Loop powered instruments draw their entire budget through the same two wires that carry the signal, so every milliampere matters. A dual isolator at 1.5 mA per channel plus a shunt amplifier plus a microcontroller is already most of a 4 mA budget, which is why the family kept a 1 Mbps ceiling and a low current core rather than following the faster parts upward. Every component added to that chain has to be judged against the same budget, and a pull up resistor that draws more than the isolator is the usual place the budget is lost.
Where this order code fits
It is used for bidirectional control and status links in loop powered instruments, isolated serial ports, industrial input output modules and any low power board that needs two signals across one barrier. Teams comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.
Questions buyers ask
Is ISO7421FEDR a valid order code? It does not appear in the vendor orderable addendum for this family, which lists the D and DR suffixes. Confirm the string before quoting or ordering.
What is the difference between ISO7420 and ISO7421? Channel direction. The ISO7420 has both channels forward and the ISO7421 has one channel in each direction.
Can it run faster than 1 Mbps? No. The 1 Mbps limit is a family limit, and a faster link needs a different isolator family rather than a different suffix.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.