Contact Us

ISO7041DBQR

Brand: Texas Instruments
Texas Instruments ISO7041DBQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7041DBQR — Power Management & Signal Chain | Superb Automation

ISO7041DBQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7041DBQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7041DBQR: The 3.5 Microamp Per Channel Quad Isolator With Three Channels Forward

ISO7041DBQR is an ultra-low power four-channel digital isolator in a QSOP (DBQ) body of 16 pins. It draws 3.5 microamps per channel with no signal moving and 116 microamps per channel at 1 Mbps, which is what makes a four-channel barrier possible inside a loop-powered transmitter.

Order code and package

Ordering stringISO7041DBQR
PackageQSOP, 16 pins, DBQ body, 6.4 mm by 5.2 mm pocket in tape
Carrier2500 pieces on a large reel, 330 mm reel, 12.4 mm tape, pin 1 quadrant Q1
Tube siblingISO7041DBQ, 75 pieces in a tube, same die
Temperature rangeMinus 55 to plus 125 degrees Celsius on the reel row
Part marking7041
Moisture levelLevel 2, 260 C peak reflow, one year floor life
Channel directionThree forward, one reverse
Default outputHigh, the F suffix reverses it to low

Electrical parameters that decide the application

Signaling rateUp to 4 Mbps at a 3.3 V rail
Quiescent current per channel3.5 microamps at 3.3 V
Current per channel at 100 kbps15 microamps at 3.3 V
Current per channel at 1 Mbps116 microamps at 3.3 V
Dynamic current ceilingUnder 120 microamps per Mbps per channel
Supply range1.71 to 1.89 V, or 2.25 to 5.5 V, set independently on each side
Level translation1.71 V to 5.5 V across the barrier
Common mode transient immunityPlus or minus 100 kV per microsecond, typical
Isolation rating3000 VRMS per UL 1577
Projected barrier lifeAbove 100 years
ESD across the barrierPlus or minus 8 kV IEC 61000-4-2 contact discharge
Temperature at 1.8 VMinus 55 to plus 105 degrees
Temperature at 2.25 to 5.5 VMinus 55 to plus 125 degrees
Certifications namedUL 1577, DIN VDE V 0884-11, CQC, TUV, CSA, IECEx and ATEX
Input thresholdCMOS, no external pull resistor needed
Isolation barrierDouble capacitive silicon dioxide

Family variants and how they differ

ISO7041FDBQRSame silicon, default output low when input power is lost
ISO7041DBQSame die in a 75 piece tube instead of the 2500 piece reel
ISO7041-Q1Automotive grade, named in the same addendum as another qualified version
ISO6741FDWR50 Mbps quad in a wide body when 4 Mbps is not enough
ISO7741FDWR100 Mbps quad, the throughput member of the same channel count
ISO6721FBDRDual channel one each way, when only two lines cross the barrier

Points to check before this part goes on a BOM

4 Mbps is the ceiling and it applies at 3.3 V. A 5 V rail does not buy extra rate on this part, so an isolated SPI bus running above 4 MHz has to move to the ISO674x or ISO774x family.

The 3.5 microamp figure is a static number. At 1 Mbps the same channel draws 116 microamps, so the supply budget follows the duty cycle of the data and not the quiescent line in the table.

The F suffix reverses the default state on power loss. A UART receive line that has to sit idle high while the far side is unpowered needs the plain ISO7041, and a line that must read low needs the F.

The addendum prints ISO7041FDBQR against a 75 piece tube cell although every other reel row of the family carries 2500 on a 330 mm reel. Confirm the carrier on the shipping label before the line is planned around a reel.

The QSOP body is 16 pins on a 0.635 mm pitch, which is finer than the SOIC bodies used by most of the other isolators on the same board. A stencil aperture set copied from an SOIC footprint will bridge on this body, so the paste print has to be checked before the first panel goes through.

The hazardous area certifications named for this part matter for a transmitter that sits in a classified zone. ATEX and IECEx appear as approvals rather than as operating limits, and the intrinsic safety argument belongs to the whole loop rather than to the isolator alone.

Where the four channels usually go

In a loop-powered field transmitter the barrier carries one UART pair, one interrupt back to the controller and one enable or alarm line. That is exactly three forward and one reverse, which is why the channel split of this part matches the application rather than the other way round.

In an isolated GPIO bank the same part is used with all four channels in one direction, and the reverse channel is simply left with its input tied to the local ground. Tying an unused input low keeps the channel from toggling on noise and adding to the supply current.

What the barrier carries in a loop-powered transmitter

A two wire transmitter draws its whole supply from the loop, which is usually 4 mA at the bottom of the scale. Every microamp that crosses the barrier is taken from that budget, so the isolator is one of the few parts where a quiescent current of a few microamps changes what the product can do. At 3.5 microamps per channel with the signal idle, four channels cost 14 microamps, and the same four channels at 1 Mbps cost 464 microamps while data is moving.

That difference is why the channel count and the duty cycle have to be looked at together. A UART that sends a burst of a few hundred bytes twice a second leaves the barrier idle most of the time, so the average sits close to the quiescent figure. A channel that carries a continuous clock has no idle time at all and the average moves towards the 116 microamp row.

What to check when the reel arrives

The barrier is only as good as the part that was actually shipped. Two checks are worth doing at goods in: the marking on the body should read 7041, and the moisture indicator in the bag should still show the dry state, because the reel row carries level 2 with a one year floor life and a bag that was opened and resealed on a distributor shelf cannot be told apart from a fresh one.

The second check is the carrier. The addendum prints the reel row at 2500 pieces on a 330 mm reel with 12.4 mm tape, and one row of the F string prints a 75 piece tube against a reel quantity. That kind of print slip is common in family addenda and the only reliable resolution is the label.

Where this order code fits

The barrier is chosen when a 4 to 20 mA transmitter has to keep its measurement front end floating and still talk to a controller on the other side of the loop. Teams comparing it with a neighbouring part start from our Component Lead Time Solutions page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

What separates the plain part from the F suffix? Only the state the output takes when the input side loses power or signal. The plain part holds the output high and the F holds it low, and the rate, current and barrier are identical.

Can one side run at 1.8 V and the other at 5 V? Yes. Each side has its own supply pin and the part translates between 1.71 V and 5.5 V, so a 1.8 V FPGA and a 5 V driver can share one barrier without a level shifter.

Is 4 Mbps enough for an isolated SPI link? It depends on the clock. The rate figure is the data rate, so a 2 MHz clock with a return path through the reverse channel is inside the limit while a 10 MHz clock is not.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.