ISO6520FDR
Product Specifications
ISO6520FDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO6520FDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO6520FDR: two channels in one direction with a functional barrier
The ISO6520FDR is a dual channel digital isolator with both channels facing the same way. It uses a double capacitive silicon dioxide barrier with functional isolation rather than safety isolation: 450 Vrms and 637 Vdc of working voltage, and 2000 Vrms or 2828 Vdc of transient voltage for 60 seconds. That is the correct class for a barrier that separates noisy circuitry from sensitive circuitry inside one product, where the barrier is not the only protection against electric shock.
Both channels run at 50 Mbps with 11 ns typical propagation delay at 3.3 V and about 1.8 mA per channel at 1 Mbps. The supply arrangement is unusual and useful: one side accepts 1.71 V to 1.89 V and the other 2.25 V to 5.5 V, with level translation across the whole 1.71 V to 5.5 V range. A 1.8 V processor can therefore drive a 5 V isolated stage, or a 3.3 V controller can read a 1.8 V sensor, without a translator on either side.
Key data for the ISO6520FDR
| Channels | Two channels, both in the same direction, in an eight pin body |
| Rate | 50 Mbps per channel |
| Timing | 11 ns typical propagation delay at 3.3 V |
| Isolation | Functional class: 450 Vrms and 637 Vdc working, 2000 Vrms and 2828 Vdc transient for 60 s |
| Supplies | 1.71 V to 1.89 V on one side, 2.25 V to 5.5 V on the other, translation across 1.71 V to 5.5 V |
| Power | About 1.8 mA per channel at 1 Mbps on a 3.3 V rail, with 150 kV per microsecond typical CMTI |
Body, marking and reel data
| Body | SOIC D, 8 pins, 4.9 mm by 6.0 mm, or the leadless VSON REU body at 3.0 mm by 2.0 mm |
| Reel | 3000 pieces on a large reel on both body options |
| Marking | 6520F, and the F tells the reader that the default output is low |
| Handling | Moisture level 2, 260 C peak, one year floor life |
| Temperature | Minus 40 C to 125 C |
Where functional isolation is the honest answer
A motor drive has a current shunt on a switching node and a controller on a quiet ground. The shunt amplifier output has to reach the controller without dragging the switching edge along with it. No person can touch the shunt circuit, and the product already relies on other insulation for safety, so a functional barrier is sufficient and a safety rated isolator would be money spent on a certificate nobody needs.
The same reasoning applies to a 48 V telecom board, a battery management slave board and a sensor head on a long cable. In each case the barrier stops ground noise from corrupting a measurement, and the working voltage stays well inside the 450 Vrms class.
Choosing between this part and its siblings
The direction arrangement is the first decision. Two channels in the same direction suit a clock and a data line going out to a peripheral. One each way suits a bidirectional link, and that is the ISO6521. The second decision is the default state: the plain part drives high when the input side is unpowered, and the F part drives low, so a line that must not be asserted during a fault needs the F row.
The third is the barrier class. If the product has to pass a safety review where the barrier is part of the protection, the functional class is not enough and the higher rated families are required. The fourth is the body: the leadless package has a creepage above 2.2 mm, which matters when the two grounds have to be kept apart on a small board.
Functional isolators and the safety case
This family is quoted as a functional barrier, and that phrase has to be said out loud in the quotation. The 450 Vrms working voltage and the 2000 Vrms transient are the right class for separating noisy circuitry from sensitive circuitry inside one product, and they are not a shock protection barrier. A customer who needs the barrier to carry a safety case needs a different family, and the earlier that is raised the cheaper the change.
The second point is the rail pair. One side accepts 1.71 V to 1.89 V and the other 2.25 V to 5.5 V, which covers a 1.8 V processor next to a 5 V interface. A rail at 2.0 V satisfies neither window, and that is a common surprise in a product that has just moved a processor from 2.5 V to 1.8 V.
Where the isolated stage is part of a medical or a defence product, the component context is on our medical device components page and on our defence grade components page.A last point on volume: the 3000 piece reel is the only published packing, so a build of two hundred units takes a partial reel and the balance stays sealed until the next batch.